la-j494p rev 1.0,Ene kb9542q reading

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • ajbernasko
    Badcaps Veteran
    • Mar 2022
    • 229
    • ghana
    #1

    la-j494p rev 1.0,Ene kb9542q reading

    Hi, please how do i flash ec for ene kb9542q e ? I found kb9542q b and as in attachment, i fled;

    ksi4(pin 59) - jkb pin 36 - fled to pin 1
    ksi5(pin 60) - jkb pin 35 - fled to pin 6
    ksi6(pin 61) - jkb pin 38 - fled to pin 5
    ksi7(pin 62) - jkb pin 39 - fled to pin 2
    ks03(pin 42) - jkb pin 23 - fled to pin 4

    i supplied 3v externally. I am using rt809h

    laptop model is la-j494p rev 1.0, maybe i am missing something.

    Thank you
    Attached Files
    Last edited by ajbernasko; 10-29-2022, 04:10 AM. Reason: la-j494p rev 1.0,
    Tags: None
    • spike888ph
      Member
      • Jun 2015
      • 31
      • Philippines
      #2
      Re: la-j494p rev 1.0,Ene kb9542q reading

      any update here if you were able to program the chip?

        Comment

        • jagadish
          Member
          • Aug 2015
          • 14
          • india
          #3
          Re: la-j494p rev 1.0,Ene kb9542q reading

          above good information , and correct pin configuration
          we can program this chip using svod3
          Last edited by jagadish; 06-02-2023, 08:17 AM.

            Comment

            Previous template Next

            Related Topics

            Collapse
            • b0n3v
              [Help]Reading EC - T14 G1 AMD with RT809h
              by b0n3v
              Hello everyone!
              I try to read the EC ITE/IT8300FN where the bios password is stored.
              The laptop is Lenovo T14 G1 AMD Ryzen 4650U, the MB is NM-C801.

              I can't read the chip with RT809H with ITE board and PFC cable. Might be I need to do something more to enable programing mode(SPI Enable?).
              I saw the post in another forum for T14s AMD (different MB but same EC configuration and pinouts) and one user successfully read and write the the same chip with SVOD3.

              Some details what i did:
              Battery and CMOS battery is unplugged.
              I click Read and then...
              05-15-2023, 04:02 AM
            • SuperAman
              PS5 HDMI port diode reading?
              by SuperAman
              I did an hdmi port repair for a PS5 and I lost the small diode z71 SOD923 on the back of the port. I did a trace repair for pin 19 of the port as well. Without the diode I get no display at all. I tried replacing the diode twice but after I get flux on it the marking comes off so I can't tell if I have it on the right orientation. When I measure I get a reading of 1(open) and 923 in diode mode. Is 923 a normal reading for these and also which side should the reading be with regards to the arrow on the board?...
              02-03-2024, 10:16 PM
            • ducky29
              RT809H reading nand chips
              by ducky29
              Hello. Im trying to read a nand chip H27U1G8F2BTR@TSOP48 but im unable to do so. Im getting the following error
              Code:
              001: Point "read" will pop up "save" dialog box, "write" will pop up the "open" dialog box.
002: The currently selected:H27U1G8F2BTR@TSOP48, capacity: 1024Mbits, 128Mbytes.
003: Adapter model£ºRT-TSOP48-1, 0.5, 12*18, Pin to Pin
004: http://www.ifix.net.cn/thread-53859-1-2.html
005: Download device programming algorithm......
006: Algo update OK
007: >------------------------------------OK---------------------------------------<
              ...
              03-01-2021, 01:46 PM
            • Fuzzy Fix
              0.00 ESR reading on a capacitor
              by Fuzzy Fix
              Howdy all I have a 90uF Capacitor 200/275 VRMS and measured the ESR . Reading says 00.3 Ohms and about 1/2 a second later 00,0 and says low ESR (Really No Kidding).
              I have checked it on the multimeter and reading is 94.7uF well within soec as ir has a 25% tolerance on it.
              Can anyone advise me is this capacitor likely to fail in the near future or still good to use.
              1 Photo
              07-26-2024, 12:05 AM
            • kalilinux25
              no 3v and 5v section voltage reading
              by kalilinux25
              Hi my board is HUSK MB 11309-248.4TU05.021

              The board is plugg and consuming 13 milliamp
              measuring the 3v coil no reading and the 5v coil no reading


              Ive measure the pins in PU4103 ( RT8223M)
              1- NO READING
              2- NO READING
              3- 4.4V
              4-NO READING
              5- NO RADING
              6- NO RADING
              7-3.3V
              8- 5V
              9-19V
              10- NO RADING
              11-3.3V
              12- 3V
              13-
              14
              15
              16-4.4V
              17-3.3V
              18- NO READ
              19-5V
              20- NO READING
              21-2V
              22-2V
              23-NO READING
              24- 5V
              ...
              01-27-2020, 03:01 AM
            • Loading...
            • No more items.
            Working...