Re: 840 G2 Machine Is Not In Committed State
Here is the only BIOS file I have.
Thank you
Here is the only BIOS file I have.
Thank you
-
-
Re: 840 G2 Machine Is Not In Committed State
I made a big mistake, I confused the Bios chip with that of the eeprom. Here is the correct file. I'm sorry, I'm learning... Thank you for your help and understanding.Comment
-
Re: 840 G2 Machine Is Not In Committed State
Here is the correct fileComment
-
Re: 840 G2 Machine Is Not In Committed State
IS WORKING ...
Last edited by infomaxcenter; 05-23-2023, 04:25 AM.Comment
-
Which file need to flash? M71_0113+outimage.bin or old 16.+mb.bin or old 2mb.bin?Comment
-
Done thanks to the file infomaxcenter!Comment
-
Hi all just wondering if anyone can help?
i have just recovered my bios after i screwed it up after trying to take a dump of my bios with a clip and a programmer to get around the bios password on one of my old work laptops (HP Elitebook 850 G1).
since the recovery i have been left with the PC now booting up but now i get the warning the machine is not in a commited state and the laptop swithes itself of after about 30 minutes, which i believe is to do with a missing intel management engine.
if anyone can shed any light on wither of these problems,... -
Hi all,
My Samsung Galaxy Book 2 Pro 15.6-inch laptop has no display and won't boot.
The charging red LED lights up, but the charging screen doesn't show any indication.
When I press the power button, the blue LED cycles on and off three times, then the screen doesn't turn on, and the device won't boot.
(I've tried removing the battery and resetting the device, but the issue persists.)
NoteBook Model name : Samsung NT955XED-KK51G(Galaxy book2 pro, i5-1240p, 15.6inch AMOLED)
PCB model name : Venus2-15-5G(REV1.2), Venus2-15 ADL NPC
S/N : 5RNK9FFT70... -
Hi everyone
I noticed on the Xgpro software the BIOS backup files have extra bytes at the end when reading some chips, this is because the Xgpro software also reads the OTP region of those flash chips, and by default will append that region to the saved file
Programmer models: XGecu TL866II Plus / T48 / T56 / T76
Example: GD25LQ128D (1.8V), IC size is listed as 0x1000000 Bytes (16777216 bytes) + 0xC00 bytes, those extra 0xC00 bytes will be appended to the end of the saved file by default, resulting in a file size of 16780288 bytes
There's also an extra OTP Secu.R... -
Hello everyone,
I’m currently working on a dead MSI GP75 Leopard (MS-17E71) motherboard (i7 CPU, NVIDIA GPU) with a no display/no backlight issue initially. After extensive investigation, I’m at a critical stage involving EC firmware, BIOS/ME region interaction, and possible deep corruption. I'm seeking advanced insight from anyone with experience in EC/BIOS sync issues or PCH-level behavior. Here’s a full breakdown:
🧩 Initial Issue- Board powers on (fans spin, keyboard lights up and can be adjusted, caps lock led lights), but no display or backlight
- External display (HDMI) shows
07-24-2025, 02:17 PM -
Hello to all of you! I need help with a BIOS file.
The BIOS chip is fried on my Asus F542UN laptop, and I bought a new chip that needs programming. I have a CH341a programmer but I need a .bin BIOS file. On Asus support page the firmware has another extension, .310 and from reading on this forum I understand that that file is not complete BIOS.
So, in short I need the "complete" BIOS .bin file to flash on the new chip. Another issue is that on back of the case the label says F542UN but on the sticker on the motherboard it's X542UN.
Comment