Re: Recovered 850 G1 Bios now the warning machine not in committed state
Does NeoProgrammer work with CH341a programmer
The Ninja
Ginjaninja
Member
Last Activity: 06-06-2023, 03:49 PM
Joined: 08-23-2021
Location: Liverpool
-
Re: Recovered 850 G1 Bios now the warning machine not in committed state
Also before i write the bios file to the chip, do i erase the chip first or can i just write over the old bios data.
TIA
The NiNjaLeave a comment:
-
Re: Recovered 850 G1 Bios now the warning machine not in committed state
Hi Hardware1
i can confirm this is the serial number
Thanks Again
The NiNjaLeave a comment:
-
Re: Recovered 850 G1 Bios now the warning machine not in committed state
here is the dump of my bios chip which is currently giving the message at start up "Waring: Machine Not in Committed State"...Leave a comment:
-
Re: Recovered 850 G1 Bios now the warning machine not in committed state
cant seem to get a close enough image with the camera but using a magnifying glass both chips appear to be the same
WINBOND
25Q128FVSG
1417
Does this correct
TIA
The NiNjaLast edited by Ginjaninja; 06-05-2023, 02:18 PM.Leave a comment:
-
Re: Recovered 850 G1 Bios now the warning machine not in committed state
Good evening all
Got the rework station and going to desolder the chip from the HP Elitebook 850 G1.
A couple of things:
1. In the attached image is that the correct chip i need to remove.
2 is the CH341A programmer OK to read this chip.
then after i have read the chip do i just post here and hpoefully one of you guys can clean it up.
TIA
The NiNja...Leave a comment:
-
Re: Recovered 850 G1 Bios now the warning machine not in committed state
Unfortunately i think i lost my original backup when i updated my laptop to windows 11. to be fair i don't think the backup i took was good as probably why i knackered the bios up in the first place.
so i am just waiting for the rework station to arrive, but when it does I'm assuming i need to de-solder the chip and plug into my programmer to get a dump of the back up as it is, then post on here to hope someone can clean it up for me. once i have a clean bios version i would just reprogram the...Leave a comment:
-
Re: Recovered Bios now the warning machine not in committed state
sorry for being a thicko, but do i need a dump from my Bios or can all these tools be ran on the laptop with the issue and get the data required. But im guessing i need to use the clip or get the soldering tools out if i need to fix my issues.
when i last used the clip i dont recall getting the right results from the bios chip, just ordered a solder rework tookfor work so may have to give that a try.
Thanks again for the replies
The NiNjaLeave a comment:
-
Re: Recovered Bios now the warning machine not in committed state
just one other question do i need to use my bios clip and prorammer to use the Intel FIT
TIA
The NiNjaLeave a comment:
-
Re: Recovered Bios now the warning machine not in committed state
thanks very much for the reply i'll have a read
Thanks the NiNjaLeave a comment:
-
Recovered 850 G1 Bios now the warning machine not in committed state
Hi all just wondering if anyone can help?
i have just recovered my bios after i screwed it up after trying to take a dump of my bios with a clip and a programmer to get around the bios password on one of my old work laptops (HP Elitebook 850 G1).
since the recovery i have been left with the PC now booting up but now i get the warning the machine is not in a commited state and the laptop swithes itself of after about 30 minutes, which i believe is to do with a missing intel management engine.
if anyone can shed any light on wither of these problems,... -
Re: HP BIOS unlock tool
Managed to get the programmer connected and get a save of the chip and then create an unlocked bios however now it won’t reboot just a flashing caps lock any ideas
using CH341A with CH341A programmer software and chip is W25Q128FV instsllat in a HP Elitebook 850 G1Last edited by Ginjaninja; 08-26-2021, 05:28 AM.Leave a comment:
-
Re: HP BIOS unlock tool
Hi all I have a HP Elitebook 850G1 laptop which is my old work one, it has a locked bios, the chip is a winbond 25Q128FV
I have bought a CH341A tool and trying to use software from one of the posts here As programmer and another one, but none seem to work.
When I connect the clip on the bios I sometimes get the little orange light on but whenever I hit read it goes to 100% and all I get is FF's across the board.
Any help would be appreciated
The ninjaLeave a comment:
No activity results to display
Leave a comment: