I need to buy a new connector like this one. It is for a FAN of a laptop but I don't know the name of it.
Anybody does?
Anybody does?
Attached Files
-
-
Re: Whats the name of this FAN connector?
The manufacturers name is on top, ACES .If there`s a schematic or boardview available for the motherboard it might have the actual part number ,such as ACES 123456A ,but it might not be available to buy as a single part only in bulk.Do you have any donor boards that you can scavenge from.
What is the motherboard part number ?
.Last edited by SMDFlea; 10-29-2022, 04:21 AM. -
Re: Whats the name of this FAN connector?
I found this connector on multiple boards but I couldn't get it off without breaking. Ill try to see if I can find one where I can find a schematic forComment
-
Re: Whats the name of this FAN connector?
Apply some flux on pins of the connector and then put some solder on it. Use a sharp object like blade and while holding the soldering iron onto GND point, try to push the blade inside. This way you'll be able to disconnect the two corner points one by one. Then proceed in same way for other pins. Dont force too much ,else you'll damage the pcb footprint. Otherway round is to apply heat on the other side of the fan connector and wait till it gives way.Comment
-
Hi All -
I had replaced my ASUS 4090 Strix cooler with a waterblock and put the stock cooler on the shelf. Was moving it and snagged my sweater on the connector and pulled the wires out of the pins on the RGB connector. I tried to get them back on but its too small so I opened the stamped pins and tried to solder but its not a good repair and the wire broke on reinstallation.
Looking to replace the connector on the cable side and get pins to crimp onto a new cable. Bought random JST and such but nothing is correct. Can anyone help identify the connector and possibly matching... -
Hello All,
tl;dr: minimal electronics experience and my first repair, lifted 8 pads off the laptop display LED controller board when attempting a connector replacement, options are attempting pad repair or jump wiring.
Laptop Model: MacBook Pro 15 Mid-2014 Retina, A1398 MGXA2LL/A
eDP Display: Samsung LSN154YL01-A02, assembly sold as Apple part 661-8310
Soldering Equipment: Hakko FX-888D w/ T-18 tips (Chisel, Conical, Bevel types)
I needed to replace the 30-pin I-PEX Cabline connector (labeled J8300 in the Apple 820-3662 mainboard schematics),... -
Hi guys,
i have a damaged keyboard connector on my older Toshiba Satellite M50-A laptop. I know there is LA-A481P motherboard. In attachment pictures there is a real looking connector and i also found a schematic to the connector. But i need help with finding a real electronic part to replace the damaged connector. e.g. on aliexpress (or different page).
It is 34pin connector and the length from pin n.1 to pin n.34 is 26mm. So it means a pitch length is 0.764 mm. I have seen connectors with 0.5mm , 0.7mm , 0.8mm and 1mm pitch length. But not with 0.75. Is it some special custom connector... -
Hi everyone
I have a 70mai Dash Cam A510 which failed after about 3 months of being installed in my car, likely due to heat, i got it from aliexpress so no point in trying to return it for warranty (and shipping it back would cost me almost the same as a new one from ali)
The camera would boot loop showing 70mai logo on the screen, sometimes it would boot fine then the live view would freeze or display purple lines
I already took it apart, and found out that the camera boots fine if i unplug the camera module from the main PCB, sometimes "playing" with the connector... -
Trying to identify where to source the LCD connectors on the motherboard side for a HP 14-cf2051la. This one came in with liquid damage to the connector and the flex cable. It appeared to clean up ok, however customer says that display blanks out intermittently. It's a 30 pin EDP flat ribbon cable on motherboard side. Believe it to be a HEDWIG-6050A3155301-MB-A01 motherboard.
I've stolen the connector from another HP motherboard which matches up but it's not the best since it's been kicking around my donor pile for a while. This connector is different to most flip type ones I have...
Comment