clickpad and trackpoint not working - la-a342pp

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • rediii
    h???, spurrrn
    • Mar 2018
    • 485
    • somewhere in europe

    #1

    clickpad and trackpoint not working - la-a342pp

    hello, laptop is yoga 12 thinkpad with described issue. all lines EXCEPT BYPASS (bidirectional, i don't know what this line is for) via schematic are present (clock, data, vcc etc.). checked resistors, values are correct and lines are continuus. i flashed the latest bios (and tried different configurations) and checked conditions under linux, same problem. do you think i should replace and/or reflash the kbc? haven't had this issue, that these devices stopped working completely. thanks for help
  • rediii
    h???, spurrrn
    • Mar 2018
    • 485
    • somewhere in europe

    #2
    Re: clickpad and trackpoint not working - la-a342pp

    whatsoever, replaced kbc and reflashed it. tp is working now

    Comment

    Related Topics

    Collapse

    • Stanley1843
      Screen Display Vertical Multicolor Lines
      by Stanley1843
      Hello, I have a screen in where sometimes when I open it pop-up vertical multicolor lines (I would say the most of them are green). If I tun off and turn on the screen the lines dissapear or if I leave open the screen after approximately five minutes the lines gone. I measured the below voltages on the main PCB and on the T-CON board and the voltages are the same when it doesn’t display the vertical lines and when it displays the vertical lines. Also, I cleaned all the connectors very good with IPA. I moved back and forth the connectors and the COF tabs but the vertical lines didn't displayed...
      06-29-2024, 11:54 AM
    • MMH3
      Dell Optiplex 5050 SFF - strange behavior and service_mode jumper not working anymore
      by MMH3
      Hello,

      i have many 5050sff. all of them, and how i experienced over many years for all about 250 DELLs goin through my hands, are fully flashable and can be serviced in any way when the service_mode jumper is set.
      Never ever i experienced problems with that.

      Now i have one 5050sff machine, where this jumper isnt working at all.
      I do not get the normal messge that the jumper is set when booting and a short test with FPT just confirms this. Everything is locked -->> EVEN for reading !?

      The history of the machine is that i used it in my office...
      03-23-2025, 09:28 PM
    • DynaxSC
      GIGABYTE X299 AORUS ULTRA GAMING - SATA PORTS 4-7 NOT WORKING ???
      by DynaxSC
      Hi,

      I have the above mentioned bord after repair, which was related to a lot of missing smd devices on the back of the board.
      There were almost 20 devices missing, caps, resistors and some diodes/mosfets.
      The board is generally working now, all PCIe ports are working, Windows installs normally.

      However I have a problem with SATA ports 4-7 (the board has 8 SATA ports) - disks are not beeing recognized by the BIOS neither by Windows (which is usually normal in case BIOS does not recognize them).
      The SATA 4-7 driver network is quite simple chipset<->buffers/drivers<->SATA...
      03-10-2025, 12:27 PM
    • obelix24
      Macbook Air 2020 (a2179) - touch id not working
      by obelix24
      Hi i have one Macbook Air 2020 where touch ID is not working (it's not scanning fingerprints). Touch ID was working before, there is no error message during scanning fingerprint it's just not scanning on screen you can see only fingerprint but there are no red updates as when it's working. Power button is working fine.

      I've checked boardview and also schematics but i'm not able to find anything related to TouchID ... i have similar issue on a2338 where there was problem with PP3V0_TOUCHID​ and after replacing UT610 it was working but here i'm not able to find anything related to...
      02-09-2025, 12:57 PM
    • hopkok
      Lenovo Legion 16ITHg6 NM-D721, keyboard not working, LEDs too
      by hopkok
      Hi masters, I need your help.

      I am working on Lenovo Legion 16ITHg6
      Motherboard number NM-D721, no BV, no schematic but I am attaching very closes ones.

      INPORTANT: My motherboard version is with IT8258 IC, that is controlling keyboard and RGB LEDs.

      My problem is on UI142, +3VALW_AG is not stable, floating from 0V to 3,3V.
      AGKB_PWR_EN_N signal is floating too (that is why+3VALW_AG not stable).
      Power LED is not working as well, power button working well.
      UI26 ??? is there any firmware too? Powered by +3VALW_AG.

      Motherboard...
      05-04-2025, 09:35 AM
    • Loading...
    • No more items.
    Working...