Hello guys.
What software between Flexbv & Nextbvdo do you beleive is better for desktop and laptop motherboards, smartphones and VGA cards?
Stanley1843
Member
Last Activity: 04-21-2025, 03:20 AM
Joined: 05-22-2024
Location: Geae
-
Flexbv Or Nextbv Softaware for PCB Viewer?
-
Hi,
the "GV-NX76T256D-RH" schematic pdf is an example. I just would like to learn if the old and fresh dump does not include all the files from the XinZhiZao because this file I couldn't find it both in old(11-29-2024, 07:46 PM) and fresh dump(01-09-2025, 01:44 AM).
... -
Hello... one question if you please. I tried to find the "GV-NX76T256D-RH" schematic pdf but I couldn't find it. On the XinZhiZao v4.47 it exists. This fresh dump does not include all the files?
...Leave a comment:
-
Thanks a lot.Leave a comment:
-
VGA card GV-NX76T256D-RH V3.0 - Looking For Schematic
I can't find a schematic of this VGA card [U][COLOR=#16a085][B]GV-NX76T256D-RH[/B][/COLOR] [COLOR=#e74c3c][B]V3.0[/B][/COLOR][/U]. I have one pdf schematic from GV-NX76T256D-RH V1.0 but it isn't the same. If anyone have or knows where I could find it please tell me.
[URL]https://www.gigabyte.com/gr/Graphics-Card/GV-NX76T256D-RH-rev-30#ov[/URL]I can't find a schematic of this VGA card [U][COLOR=#16a085][B]GV-NX76T256D-RH[/B][/COLOR] [COLOR=#e74c3c][B]V3.0[/B][/COLOR][/U]. I have one pdf schematic from GV-NX76T256D-RH V1.0 but it isn't the same. If anyone have or knows where -
Hello, does anyone have a schematic or a boardview from the VGA card GV-NX76T256D-RH?Leave a comment:
-
Hello, with thermal camera I found that this IC regulator (RT8057GQW - SMD Mark: J7) was shorted. As I read on the internet this regulator was responsible for the WiFi & Bluetooth supply (please correct me if am I wrong). I removed it (without replace it) and the short was gone and the PS3 starts and shows image. Many thanks [B][URL="https://www.badcaps.net/member/169795-lotas"]lotas[/URL].
[url]https://www.richtek.com/Products/Switching%20Regulators/DC_DC%20StepDown%20Convertor/RT8057?sc_lang=en[/url]
[url]https://www.richtek.com/assets/p...Leave a comment:
-
If you please could you tell (draw in picture) me which capacitors do you mean? Thanks for your reply and the guidance.Leave a comment:
-
Hello,
I measured it again... 6 Ohm between these two pins. Now when I connected it to the 230V the indicator don't light and the PS3 doesn't start at all....Leave a comment:
-
PS3 Slim Turns OFF Immediately After Turning ON
Hi, my PS3 Slim (CECH-3003A) when I connected to 230V the PS3 the indicator of the switch is red and after pressing it the is green (fan spins) for only 10 seconds and then completely off. Some times also is completely off when I connected to 230V.
On the CN101 connector at the 5VSB pin I measure 0V.
Without the CN101 connector pluged in the PS3 board (on the fly) I am measuring 5V on the 5VSB on the power supply side.
On the 5VSB in respect to ground I am measuring 6 Ohm resistance. There is any schematic to find which ICs supplied from 5VSB or any suggestions where l have to... -
[SIZE=14px][FONT=Calibri]New update:
I check the voltage with oscilloscope on the CPU coils and the CPU don't have the proper voltage. If touch the CPU when the fan spins is slightly hot.
I measure the pulses from the 15,18,19 pins of ISL6565BCRZ (Multi-Phase PWM Controller) and looks OK. Also, these pulses arrive at the pin 3 of each ISL6612ECB-T (Advanced Synchronous Rectified Buck MOSFET Driver) respectively.
The problem in my opinion is at the output pin 1 that drives the high side mosfet. And in three chips ISL6612ECB-T the pulses are weak and seems like a noise.
I...Leave a comment:
-
Hello,
I received the PCI tester cards from the alliexpress and I attached on the motherboard.
The one of them show nothing "--".
The second show "0000".
The third show "FF".
As I saw in a "PC Analyzer Users Guide" pdf that I found on the internet:
The "00" means "Code copyng to specific areas is done. Passing control to INT 19h boot loader next.
The "FF" means "Flash ROM programming was succesful. Next restarting the system BIOS."
Do you know what these codes...Leave a comment:
-
At the below image are the vertical multicolor lines....
Leave a comment:
-
Screen Display Vertical Multicolor Lines
Hello, I have a screen in where sometimes when I open it pop-up vertical multicolor lines (I would say the most of them are green). If I tun off and turn on the screen the lines dissapear or if I leave open the screen after approximately five minutes the lines gone. I measured the below voltages on the main PCB and on the T-CON board and the voltages are the same when it doesn’t display the vertical lines and when it displays the vertical lines. Also, I cleaned all the connectors very good with IPA. I moved back and forth the connectors and the COF tabs but the vertical lines didn't displayed...
-
BEST 505 Vs Mechanic Brand Reballing Balls with Lead
Hello,
has anyone use these Brands of solder balls? The brand BEST writes on the label of the jar the specs of the solder balls instead of the Mechanic brand. I beleive that BEST brand must be more professional (in labeling at least) but I have never try one of them so I would like your opinion. By the way I hardly can I find the Mechanic brand in aliexpress (the only where I found was lead free solder balls) and on ebay these that I found are approximately15USD per jar. If you know any other trusted brand of solder balls please tell me. -
Thanks again for your help....
Leave a comment:
-
Thanks for your reply. You mean something like this?
[url]https://vi.aliexpress.com/item/1005001757643087.html?gatewayAdapt=glo2vnm[/url]https://Thanks for your reply. You m...=glo2vnm[/url]...Leave a comment:
-
Do you know any trusted "Post Card" (part number or brand or link) to suggest me to buy?Leave a comment:
-
Could you suggest me to buy a "Post Card" (part number or brand or link)? I always want to buy one and now I think it is the time.
For this motherboard I couldn't find a manual and I found a manual from another model of motherboard where it seems that is the same from what I check in my motherboeard (I don't know if you know a site that I could find it)....Leave a comment:
-
First of all many thanks for your time to reply me. What do you mean by "Do you have a post car"?
This mainboard is from an old PC that controls a CNC laser router.
It doesn't have a speaker solder on the PCB neither have in the panel. I started without a RAM but doesn't beep and makes the same thing again. Do you know if can I connect a buzzer (how can I find the pins - if it has pins for speaker/buzzer)?
Do you suggest me to change all the capacitors?
One thing that I remebered. I had the same motherboard before some years where was working fine and I...Leave a comment:
No activity results to display
Leave a comment: