MBA 13 820-3437 sensor error

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • MobileXT
    Badcaps Veteran
    • Oct 2012
    • 214
    • USA
    #1

    MBA 13 820-3437 sensor error

    I working on a MacBook Air 13 2014 820-3437 with the following error Thunderbolt Proximity, MLB Top Side, Airport Proximity, Memory Proximity and Trackpad Skin. I almost replaced all the sensors already and still have the same results. I attached a Photo here.
    Attached Files
    Tags: None
    • piernov
      Super Moderator
      • Jan 2016
      • 4439
      • France
      #2
      Re: MBA 13 820-3437 sensor error

      Check if all the same sensors fail without touchpad plugged in.
      If yes, probably an issue on SMC "3" SMBus.
      Check resistance across R5390 and R5391.
      Check voltage and diode mode to ground on SMBUS_SMC_3_SCL and SMBUS_SMC_3_SDA.
      OpenBoardView — https://github.com/OpenBoardView/OpenBoardView

        Comment

        • MobileXT
          Badcaps Veteran
          • Oct 2012
          • 214
          • USA
          #3
          Re: MBA 13 820-3437 sensor error

          I did unplug the keyboard and trackpad and the rest of the error are disappear except the trackpad Skin. So I concluded that the track pad must be bad. Thanks!

            Comment

            • jimmyspangle
              New Member
              • Feb 2021
              • 1
              • UK
              #4
              Re: MBA 13 820-3437 sensor error

              Trackpad cable.

                Comment

                Previous template Next

                Related Topics

                Collapse
                • groomit
                  Google Pixel 5 - Proximity Sensor Issues - Reflow/Replacement procedure tipps wanted
                  by groomit
                  Hi,
                  I just replaced the battery on a Google Pixel 5.
                  After that the proximity sensor isn't functioning properly any more. It is constantly activated. So when playing a voice message on Whatsapp, the Screen instantly turns off.
                  Checking with a sensor app I can verify weird behavior of the sensor. It is triggered when nothing is near and sometimes works correctly when squeezing the phone next to the sensor hole.
                  The rubber seal is on again (as mentioned in various suggestions in other forums).

                  This smells like a cold or broken solder joint. So I'd like to reflow...
                  06-11-2025, 02:21 AM
                • Benass
                  TestIFire 1000 IR Sensor Clean Cup Error
                  by Benass
                  Hello,

                  I have a TestiFire 1000 Device with an IR sensor fault. The problem was that the IR sensor had no power.

                  Initially, I found that R47 had 5V, but it was OL (open loop). I replaced it with another 100 Ohm resistor, and 5V was restored to the IR sensor.

                  The second problem I found was that R50 (I think) was 4700, but it was also OL. I replaced it with another 470 Ohm resistor.

                  Despite these fixes, the device was still giving me an IR sensor error. At this point, I was about to give up, until the owner advised me to attach the CUP to...
                  04-23-2023, 09:08 AM
                • Sus256
                  HISENSE 65E7KQ PRO - no boot
                  by Sus256
                  Hi all!

                  HISENSE 65E7KQ PRO
                  RSAG7.820.13512 - chassis
                  MT9618BAATAB - cpu
                  RSAG7.820.12059 - power
                  HD650Y3U77 - panel
                  KLM8G1GETF - emmc

                  The TV does not turn on, the standby indicator is on. All voltages are present.
                  Emms is dead. Not readable, not detected.
                  Replaced emmc.
                  But with another dump there is no launch

                  Terminal log

                  UART
                  <
                  AC_ON
                  RPMB key is not yet programmed

                  HASH1_VERSION=0x00000000 64bit
                  E-B
                  FDE enabled
                  layout pattern onebin by SAR7,0...
                  06-01-2025, 02:11 AM
                • sushilachuthan
                  APC UPS error P13
                  by sushilachuthan
                  one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
                  the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
                  The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
                  We replaced the SCR with new device,, but the device is not power on as expected.

                  Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....
                  09-26-2025, 09:00 AM
                • Superbee_dad
                  Sharp 80” long short flash backlight error - Help
                  by Superbee_dad
                  Hello Sharp TV experts
                  Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

                  > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
                  > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
                  01-24-2025, 11:51 PM
                • Loading...
                • No more items.
                Working...