hp 450 g3 it will not start

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • poweron
    Badcaps Veteran
    • May 2019
    • 365
    • italy

    #1

    hp 450 g3 it will not start

    main: DAX63CMB6C0 REV: C
    with this notebook something a little strange happens when I connect the power supply connector, the relative LED of the connector lights up and at the same time also the LED on the on / off button for three seconds then turns off while the other stays on, if I try to press the button on / off does not turn on, I measured on the button pins and I measure 2.4v (usually 3.2v), which go to ground by pressing the button, +3 and +5 voltages are present, what tests can I do? can it be a corrupt bios problem?

    thank you
  • SMDFlea
    Super Moderator
    • Jan 2018
    • 20737
    • UK

    #2
    Re: hp 450 g3 it will not start

    check voltages on PU3 ,all pins, post your results. The power button needs +3V_ALW. Also check voltage on CN5 with and without the ribbon cable attached
    All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

    Comment

    • poweron
      Badcaps Veteran
      • May 2019
      • 365
      • italy

      #3
      Re: hp 450 g3 it will not start

      I can't find PU3, nothing is printed on the card, only the model

      Comment

      • SMDFlea
        Super Moderator
        • Jan 2018
        • 20737
        • UK

        #4
        Re: hp 450 g3 it will not start

        Originally posted by poweron
        I can't find PU3, nothing is printed on the card, only the model
        Look for the Quanta X63 boardview,it here on the forum and available on the net on free schematic sites.
        All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

        Comment

        • poweron
          Badcaps Veteran
          • May 2019
          • 365
          • italy

          #5
          Re: hp 450 g3 it will not start

          measurements on CN5 both with and without flat:
          pin1 = 3.5v
          pin2 = 3.5v
          pin3 = 2.4v
          pin4 = 0

          measurements on PU3:
          pin1 = 3.4v
          pin2 = 3.4v
          pin3 = 0.6v
          pin4 = 3.5v
          pin5 = 3.5v
          pin6 = 7v
          pin7 = 4.7v
          pin8 = 19v
          pin9 = 0
          pin10 = 3.5v

          Comment

          • poweron
            Badcaps Veteran
            • May 2019
            • 365
            • italy

            #6
            Re: hp 450 g3 it will not start

            measurement on Q8:
            pin1 = 3.3v
            pin2 = 2.4v
            pin3 = 3.5v
            pressing on / off button pins 2 and 3 go to 0v

            Comment

            • SMDFlea
              Super Moderator
              • Jan 2018
              • 20737
              • UK

              #7
              Re: hp 450 g3 it will not start

              Can you remove C28 and check if the voltage goes up,if it does replace the cap.If the cap is ok Test Q8 again,i think you got the pins mixed up.
              All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

              Comment

              • poweron
                Badcaps Veteran
                • May 2019
                • 365
                • italy

                #8
                Re: hp 450 g3 it will not start

                the C28 is ok, but there is something that does not fit me, according to the dataschit the pins of Q8 should be as on the diagram but on the board it is on pin 2 that I measure the 2.4v while according to the diagram I should measure them on pin 1, and when I press the on / off botton it is pin 2 that goes to gnd and pin 3 goes to 0v, llego photo of q8
                Attached Files

                Comment

                • mcplslg123
                  Badcaps Legend
                  • Jun 2015
                  • 7262
                  • india

                  #9
                  Re: hp 450 g3 it will not start

                  I think the pin which you have markes as pin3, should be pin1.

                  Comment

                  • SMDFlea
                    Super Moderator
                    • Jan 2018
                    • 20737
                    • UK

                    #10
                    Re: hp 450 g3 it will not start

                    Originally posted by mcplslg123
                    I think the pin which you have markes as pin3, should be pin1.
                    The 2N7002K gate is pin 1. The schematic pins are wrong .
                    All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

                    Comment

                    • poweron
                      Badcaps Veteran
                      • May 2019
                      • 365
                      • italy

                      #11
                      Re: hp 450 g3 it will not start

                      as you can see in the photo the number of pins corresponds to that found on the datashits, therefore: pin 1 = gate pin 2 = source pin3 = drain, but what I would like to know when I turn on the notebook goes to gnd pin 2 source, also because pin2 of Q8 and pin 3 of CN5 are connected together. to reset the micro-ec that is to turn on the notebook, pin 73 of the micro should go to 0v right? only it is already at 0v

                      Comment

                      • poweron
                        Badcaps Veteran
                        • May 2019
                        • 365
                        • italy

                        #12
                        Re: hp 450 g3 it will not start

                        replaced Q8 but does not turn on yet, voltage on pin 2 is now 2.5v

                        also I noticed that Q6 and Q7 are not mounted
                        Last edited by poweron; 08-29-2020, 09:15 AM.

                        Comment

                        • ionut68
                          New Member
                          • Sep 2020
                          • 8
                          • Romania

                          #13
                          Re: hp 450 g3 it will not start

                          Hello
                          I have a Model X63C PCB with the same problem as "poweron"
                          How was the problem solved?
                          Poweron with what software did you open "Quanta x63C-MB_C.bdv?

                          Comment

                          Related Topics

                          Collapse

                          • corrize
                            Where to find a very small fpc connector 0.3mm between 2 pins ?
                            by corrize
                            Hello, I search this connector (oxydated).
                            It's a fpc zif low profile connector. It come from camera sensor, it is very small : 0.3mm between 2 pins.
                            I ordered 2 from Aliexpress called « 0.3mm pitch » but one was 0.5mm between 2 pins and the other 0.6mm. In fact « 0.3mm pitch » seams to be the pad width and not the distance between 2 pins.
                            I can't find it. The other websites like mouser dont show the datasheet, and I can't check if it is 0.3mm between 2 pins ?


                            Do you know how to find this connector please ? What is the exact name for find it ?

                            ​...
                            08-06-2024, 05:25 PM
                          • Tynan Dill
                            Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                            by Tynan Dill
                            I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                            Upon bringing it home and plugging it up, it showed a standby light.

                            I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                            The screen seems to blackout and stay black, but with a flashlight I can see the display.

                            With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                            Assuming...
                            11-22-2024, 01:46 PM
                          • Tomylee
                            No LCD image after connector replacement – lifted components and damaged resistor (Nintendo Switch Lite HDH-CPU-02)
                            by Tomylee
                            Hi everyone,

                            Sorry for the person who’s going to read all this !
                            I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.

                            While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.

                            During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the...
                            07-11-2025, 11:52 AM
                          • araxnido
                            Programming KBC IT8987VG ASUS TUF FX506L RT809F+PEB
                            by araxnido
                            Dear friends, I want to share my experience repairing an ASUS TUF FX506L gaming laptop motherboard: DABKXDMB8E0_F_BKXD. Boardview and schematic are available, as well as the BIOS and ITE ROM.

                            When the customer brought in this laptop, it was initially dead; it showed no signs of booting for any reason. After hours of measurements, checking each stage, MOSFET, and seeing if there was a short circuit in any capacitor, I discovered a strange 0.7V leakage voltage on the 3V_S5 rail, particularly on the PL9 coil, with the board not powered on. There were 3V_LDO and 5V_LDO voltages, which...
                            06-10-2025, 09:26 PM
                          • TimeRabbit07
                            Asus FX517ZC charges but power button does nothing
                            by TimeRabbit07
                            Hi all!

                            I've got an Asus FX517ZC on the bench at the moment and I just can't figure out what's going on with it.


                            Here are its various numbers and identifiers:
                            Model short: FX517Z
                            Model long: FX517ZC-HN114W
                            SN: NANRCX01S57842E
                            CN: 3SDB 12M
                            MFD: 2022-10
                            Motherboard model: DA0NJLMBAE0 REV E


                            Symptoms:
                            The laptop's charge light comes on, but when the power on button is pressed nothing happens. No fan spin, no caps lock, no screen or keyboard backlight, nothing.


                            History so far:
                            The...
                            09-04-2024, 05:48 PM
                          • Loading...
                          • No more items.
                          Working...