HP Pavillon G- Fan error (90B)

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • senakahks
    Member
    • May 2020
    • 39
    • New Zealand

    #1

    HP Pavillon G- Fan error (90B)

    I trying to fix a l HP Pavillon G which gives the error message 90B fan error.

    Fan is slowly running for about 2 seconds and stop about 2 seconds. that runs as a cycle. What could be the problem.

    No much dust and connector has no problem.
  • peste
    Super Moderator
    • Dec 2016
    • 12392
    • ROMANIA

    #2
    Re: HP Pavillon G- Fan error (90B)

    Originally posted by senakahks
    I trying to fix a l HP Pavillon G which gives the error message 90B fan error.

    Fan is slowly running for about 2 seconds and stop about 2 seconds. that runs as a cycle. What could be the problem.

    No much dust and connector has no problem.
    maybe the fan is blocked..take it out, check it, grease it if possible..if you can't test the laptop with another fan ..
    Due to a lack of donations, server free space at a critical level, and possible closure of Bios Requests all donations are welcome, click:

    >>>>> https://www.badcaps.net/index.php?pageid=donate1 <<<<<

    Every donation made will go towards server fees and maintenance costs.

    Comment

    • ktmmotocross
      Boardkiller
      • Feb 2014
      • 3567
      • slovakia

      #3
      Re: HP Pavillon G- Fan error (90B)

      if fan is spinning and ges in cycle mostly conroller circuit is ok. maybe bad fan tacho.
      u have 3 or 4 wires fan?

      Comment

      • senakahks
        Member
        • May 2020
        • 39
        • New Zealand

        #4
        Re: HP Pavillon G- Fan error (90B)

        3 wire fan

        Comment

        Related Topics

        Collapse

        • Sus256
          HISENSE 65E7KQ PRO - no boot
          by Sus256
          Hi all!

          HISENSE 65E7KQ PRO
          RSAG7.820.13512 - chassis
          MT9618BAATAB - cpu
          RSAG7.820.12059 - power
          HD650Y3U77 - panel
          KLM8G1GETF - emmc

          The TV does not turn on, the standby indicator is on. All voltages are present.
          Emms is dead. Not readable, not detected.
          Replaced emmc.
          But with another dump there is no launch

          Terminal log

          UART
          <
          AC_ON
          RPMB key is not yet programmed

          HASH1_VERSION=0x00000000 64bit
          E-B
          FDE enabled
          layout pattern onebin by SAR7,0...
          06-01-2025, 02:11 AM
        • Superbee_dad
          Sharp 80” long short flash backlight error - Help
          by Superbee_dad
          Hello Sharp TV experts
          Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

          > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
          > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
          01-24-2025, 11:51 PM
        • modtool
          HP Victus 15-FA1025NL , board DAG3PAMB8D0 REV:D, shorted CPU DrMOS and n-mos
          by modtool
          Hi to all,
          the owner of this machine gave it to me after having opened it to take off the dust from the inside, telling me that after that it didn't start anymore.
          I found that one of the DrMOS (AOZ5016QI) on the CPUCORE was shorted between VIN and VSWH, and that one of the two n-mos connected to the power jack was shorted aswell.
          I unsoldered the two shorted components and verified that there were no other short circuits, then decided to power the mainboard, firstly with the lab power supply, then with its original HP 200w charger, but the behaviour is the same, the board starts...
          04-01-2025, 08:22 AM
        • medinfo
          Mac T2 after update(There was an error activating your device)
          by medinfo
          Macbook Pro 2019 T2
          iCloud OFF
          MDM unlocked by changing Serial Number
          worked fine but after latest update see (There was an error activating your device. Please try again).
          Erased and boot in internet recovery, same error.
          changed to original serial number (iCloud OFF & MDM ON), same error.
          tested with others serial number, same error.
          tested (CMD+R), (Option+CMD+R), (Shift+Option+CMD+R), same error
          Revived and restored by Apple Configurator and same error.

          Any help ?
          12-31-2023, 02:04 PM
        • rmjimenez455@gmail.com
          Sumsour station 8586D error H-E
          by rmjimenez455@gmail.com
          Hello everyone, next I have the following problem with the Sumsour 8586D 110v dual station I bought it a year ago and it worked wonderfully, now it presents the H-E error on the soldering iron side, the hot air side works correctly..... I disassembled the soldering iron head because the manual tells me that this error is due to ceramic resistance problems, in effect, I measured it and it is open, I bought a new one that is working verified in a soldering iron and nothing.... The same error continues, I proceeded to open the station and check visually, I found a totally damaged 1R00 surface mount...
          09-07-2024, 09:33 AM
        • Loading...
        • No more items.
        Working...