820-3437 A1466 MBA Missing P5VS4RS3_EN U7600

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • macattack600
    Senior Member
    • Aug 2011
    • 97
    • USA

    #1

    820-3437 A1466 MBA Missing P5VS4RS3_EN U7600

    Hi I had all rails up but no PP5V_S5 problem was no SMC_PM_G2_EN I replace SMC reball I now have--- PP5V_S5 @5v and P5VP3V3_VREF2 @ 2v

    I check down rails next PP5V_S4RS3 on C7600 Fan turns on with meter probes only touching for few seconds all rails come up , all caps resistors around U7600 same thing fan runs with only meter touching for a 4 seconds and stops.

    I had green to orange light before and after I change SMC.

    When I test at Pin 12 of U7600 fan turn on for as long as I leave meter probes to.

    U7501 Pin 21 gives P3V3S5_EN_R 3.3v but P5VS4RS3_EN 0v? PCH PM_SLP_S4_L bad ? or U7600 maybe?
    Last edited by macattack600; 10-16-2016, 08:58 PM.
  • Rashid36
    Senior Member
    • Aug 2014
    • 59
    • Saudi Arabia

    #2
    Re: 820-3437 A1466 MBA Missing P5VS4RS3_EN U7600

    Bro did u find problem ???????

    Comment

    Related Topics

    Collapse

    • BMCappelletti
      Macbook Air A1466 EMC 3178 missing power and liquid damaged
      by BMCappelletti
      Hi everyone.
      Macbook Air A1466 EMC 3178 (board 820-00165 A) not turning on and no charging light. Completely dead. With no battery connected it would power up and I could hear the chime, but nothing on the screen and then a sudden turn off. Sometimes during the chime. Opened it up and found some liquid damage. The flat that connects both boards has damage in one side (with a missing pin already). The connectors on the boards are fine, though.
      Also, there was liquid damage on the included picture area, which are R8111 and C8111. A quick and soft brush on it made the resistor be gone....
      04-15-2024, 01:24 PM
    • AlexVG
      MacBook A1466 820-165-A No power Missing PM_SLP_S4_L
      by AlexVG
      Hi,

      It's me again!
      Another issue, I am not too lucky.
      I have MacBook A1466 820-165-A after another service. Most of parts have rough traces of soldering (I guess they had been troubleshooting without success)

      Missing PM_SLP_S4_L
      because absent PM_SLP_S5_L

      What processor needs to form PM_SLP_S5_L signal?

      I tried to connect U8000 and U8180 to run directly but it doesn't want to run.

      All of these signals are present:
      1. PPVRTC_G3H (VCCRTC) 3.3
      2. RTC_RESET_L (RTCRST#) 3.3
      3....
      01-29-2023, 05:50 PM
    • fichamba
      MBAir 13” A1466 missing SPI clock
      by fichamba
      Hello everybody:
      I have an A1466 (MoBo 820-00165-A) which is driving me crazy.
      It has all voltages, everything seems OK. It starts after connecting the Apple charger (fan spins normally; maybe a bit later than in a working board that I have side by side). The only (!!!) missing signal is the SPI clock.
      I have measured at pin 6 of U6100 (the SPI), and I have nothing in the scope. Neither in the data in/out pints I have data train in the scope (just a little bit sometimes).
      The working board is showing me fixed clock pulse at pin 6 of its SPI. I'm crazy about this....
      02-16-2022, 09:16 AM
    • Instafixx
      Macbook A1466 820-00165 PPBUS Missing
      by Instafixx
      Hello, I have a Macbook A1466 80-00165 which is not turning on. It is taking 0 ohms and the PPBUS_G3H is at 0v at F7140.

      Tried Injecting 1V but nothing gets hot.
      Removed the F7140 fuse and the Pin#2 is still short to ground.

      Can anyone suggest where the issue is ?
      05-20-2023, 06:42 AM
    • mcplslg123
      A1466 Missing Vcore
      by mcplslg123
      Logic Board:820-00165A

      It turns on without display. Vcore is missing. Rest all voltage are there.

      01.All_Sys_PwrGood-3.3V
      02.P1V8S3_PGood-3.3V
      03.P1V05S0_Pgood-3.3V
      04.DDRREG_PGood-3.3V
      05.P5VS4RS3_PGood-3.3V
      06.S5_PGood-3.3V

      Missing
      01.CPU_VCCST_Pwrgd. R1931 Pin1 has P1V05S, pin2 is zero.Resistance on R1931,pin1 is 110 Ohms,PIn2 is 0.885K.
      02.U7200,PIn1 VR_EN is missing. CPU_VR_Ready is present on R1955. Resistance Value of R1800 is good.

      R1931 showed incorrect value and was rusted/frozen on CPU_VCCST_PGood...
      08-16-2021, 11:44 PM
    • Loading...
    • No more items.
    Working...