how to flat bended direct heated stencils

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ktmmotocross
    Boardkiller
    • Feb 2014
    • 3553
    • slovakia

    #1

    how to flat bended direct heated stencils

    my direct heated stencils are always bended. have enybody some clue how to flat it
  • atsio
    Badcaps Veteran
    • Oct 2013
    • 819
    • Greece

    #2
    Re: how to flat bended direct heated stencils

    Two thick pieces of iron bar (I use 8mm thick) and a clamp.

    Comment

    • ktmmotocross
      Boardkiller
      • Feb 2014
      • 3553
      • slovakia

      #3
      Re: how to flat bended direct heated stencils

      absolutely didnt work. with hands i can better flat the bends.

      Comment

      • loser18
        Badcaps Veteran
        • Nov 2013
        • 274
        • UK

        #4
        Re: how to flat bended direct heated stencils

        I think he meant to get the stencil hot first...than clamp it & let it cool down...

        Comment

        • atsio
          Badcaps Veteran
          • Oct 2013
          • 819
          • Greece

          #5
          Re: how to flat bended direct heated stencils

          When I say a clamp, I mean something like this.
          And I use a lot of force.
          Attached Files
          Last edited by atsio; 06-09-2014, 11:02 AM.

          Comment

          • ktmmotocross
            Boardkiller
            • Feb 2014
            • 3553
            • slovakia

            #6
            Re: how to flat bended direct heated stencils

            same like this, lot of power, not work

            maybe get it heated first

            Comment

            • dellxps15
              Badcaps Legend
              • Feb 2014
              • 1585
              • italy

              #7
              Re: how to flat bended direct heated stencils

              i had that problem with a ps3 stencil.... thouth it was a bad china manufacter, so ordered another one and bended at second use....

              that's getting really bored when u place the ball and then the stencil bump and make them go all over...

              Comment

              • ktmmotocross
                Boardkiller
                • Feb 2014
                • 3553
                • slovakia

                #8
                Re: how to flat bended direct heated stencils

                i place some balls to corners for better stability and easy align of stencil.

                Comment

                • dellxps15
                  Badcaps Legend
                  • Feb 2014
                  • 1585
                  • italy

                  #9
                  Re: how to flat bended direct heated stencils

                  for allign i use a magnifier glasses (chinease one) and tht's an easy part , but ofcours very important, because once when i put balls and stencil not complitely alligned had some trouble to remove the stencil from the bga....

                  practive tell that all.... more u do more u get familiar wit it

                  Comment

                  Related Topics

                  Collapse

                  • BigOof
                    Marantz SR5007 popping on volume change and mute in Direct Mode
                    by BigOof
                    Hi,

                    I bought a used Marantz SR5007 and it's giving me some issues that I can't seem to really place. It functions well in most settings, ARC mostly works, it has no issues driving my speakers in any of the digital input modes, but I'm having issues running analog inputs in direct or pure direct mode. For some reason in this mode there's distortion for every volume increment I give it, but once the volume is stable it has no issues. Muting creates a loud pop, switching to another source also causes a pop and so does turning off the amp in that mode. Again, no issue in the digital modes....
                    12-12-2024, 06:15 AM
                  • dclass-pro
                    HP 440 G2 no power after short in flat lcd
                    by dclass-pro
                    Hi all guys, I need your help. On a HP 440 G2 - LA-B181P laptop I was changing the speakers and the pc worked fine everything ok.
                    After closing it all with all the screws I realized that it would no longer turn on. I opened it and found that the flat cable of the LCD was shorted. I ordered a new flat but the motherboard still won't turn on, as soon as I connect the power supply the connector LED always flashes and the power button stays on.
                    I tried to check the voltages and the 3v and 5v are there, on the battery pin (with no battery connected) I have about 2v.
                    I tried to...
                    08-11-2023, 07:47 AM
                  • reformatt
                    A2337 not working with flat battery
                    by reformatt
                    Looking for some advice on a 820-02016 board as I don't have much experience with these M1 machines. Learning the nuances of them as I go.

                    So the history of this machine was it had been in a bag where a bottle of water leaked. Presented as dead about a month ago, corrosion was mainly around the battery connector and it's sub-PCB. Some corrosion was noted on the board around UC300, CC325, CW1C7, CW1C8. That was it really.

                    Now without battery connected, USB-C will stay at 5V and cycle between 0 and 120ma. PPBUS_AON is cycling between 0 to 12.3V. If battery is connected,...
                    10-12-2023, 04:36 PM
                  • myth77
                    direct heat stencil,where do you get it? and how to prevent warping?
                    by myth77
                    So, lately i found that for smaller chips like pch it is very difficult to reball with nondirect heat stencil. So i decided to try direct heat stencils...and while i am waithing some stencils to arrive i have a few questions:

                    1. From who do you buy a quality direct heat stencils? i am reading that they can vary in quality and make a big difference...Any trusted sellers?

                    2. I am reading also the problem of warping (curving) direct heat stencils...Is it because of quality of the stencils? or/and because some preheating is also required? and help and advice here?
                    01-17-2022, 05:06 AM
                  • FuzzyOwl
                    Denon AVR-X3600H No sound even to pre outs in direct analog mode. Help please!
                    by FuzzyOwl
                    Hi, I have a Denon AVR-X3600H I'm trying to repair. I have no electronics repair experience but I have a multimeter, service manual and a will to fix it (https://device.report/m/d5de8c00e617...f63147aba9.pdf)

                    Everything seems to work except for no sound even through the pre outs. However I will get sound using Zone 2 pre outs.

                    Only digital symptom I can tell is it will soft lock when in the Speakers/Test Tone menu and be unable to adjust +/- db during the test tone.

                    I've followed the trouble shooting guide, audio check...
                    12-05-2024, 11:54 AM
                  • Loading...
                  • No more items.
                  Working...