SMD Asking equivalent, Can I replace ISL88738H WITH ISL88739

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • String2016
    Badcaps Legend
    • Nov 2015
    • 2229
    • philippines

    #1

    SMD Asking equivalent, Can I replace ISL88738H WITH ISL88739

    Can I replace ISL88738H WITH ISL88739?
  • mon2
    Badcaps Legend
    • Dec 2019
    • 13834
    • Canada

    #2
    See attached.

    Short answer - no. Many differences. See SDA / SCL for example. Different pin locations.


    Click image for larger version

Name:	pic1.png
Views:	144
Size:	465.4 KB
ID:	3526030

    Click image for larger version

Name:	pic2.png
Views:	137
Size:	202.5 KB
ID:	3526031

    Comment

    Related Topics

    Collapse

    • Document Archive
      ISL88739AHRZ ISL88739 Laptop Battery Charger Datasheet
      by Document Archive
      The ISL88739 & ISL88739AHRZ are a highly versatile combo battery charger
      configurable for operating as either a Hybrid Power Boost (HPB)
      charger or a Narrow VDC (NVDC) charger, supporting 2-, 3-, or
      4-cell batteries. Both configurations allow the battery to work with
      the adapter together to supply the system load when it exceeds
      the adapter capability, referred to as system Turbo mode. HPB
      charger configuration reverse-boosts battery energy to the system
      bus to help the adapter provide the system power in Turbo mode.
      NVDC charger configuration...
      11-05-2024, 03:28 PM
    • chth96
      Is it no harm to replace with capacitor without ripple current rating?
      by chth96
      When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


      Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
      But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
      Rubycon YK DataSheet (b...
      04-19-2024, 05:19 AM
    • RetroComputingGrotto
      Opinions/Advice on Do/Should I replace ALL Electrolytic Capacitors on old equipment?
      by RetroComputingGrotto
      I've just been repairing some (very) old speakers with a loud hum that occurred as soon as you powered them on regardless if any actual audio is played through them. I work in a School so it's 99% likey that the Teachers have hardly ever turned the power off on them for well over 10+ years.



      As you can see the top large capacitor on the right has a bulge on the top so defincately needs replacing. As the one next to it is exactly the same capacity and voltage I planned to replace them both.


      What is your advice/opinion on whether or not on old(er)...
      04-03-2024, 08:30 AM
    • chth96
      Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
      by chth96
      I have purchased an 100-240v AC/5v 2a DC adaptor from aliexpress,and a month ago It smelled burning when I plugin it powerstrip.
      Since then, This AC/DC adaptor have been out of order.
      But A few days ago,I replace 0.5 watt resistor with 1 watt resistor(1ohm) in this adapter.
      After replacing resistor,It succeed to recharge all of android phone.And When I measure voltage on the two pins of USB port,It shows 5.5v
      Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
      And Is there any possibility that it will suddenly explode as well as to be out...
      12-03-2023, 04:40 AM
    • psyduck
      Conformal coating on Samsung U32D970 monitor PSU, do I need to replace after repair?
      by psyduck
      I have a Samsung U32D970 monitor from 2015 I pulled out of the bad hardware pile that turned on and then turned itself back off after a few minutes of use and refused to turn back on. The PSU has part number BN44-00786A, and I found a couple posts about one that had blown with damage to the MOSFETs and PWM controller - but nothing about intermittent failures. I started a new thread and said that I would refresh the solder joints on the board to see if it was just a bad connection and possibly replace the PWM and PFC ICs. I then asked what my next course of action would be after those steps. I...
      11-27-2023, 06:56 PM
    • Loading...
    • No more items.
    Working...