Advent 5611: No Backlight

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • speedypro
    Badcaps Veteran
    • Feb 2013
    • 561
    • United Kingdom
    #1

    Advent 5611: No Backlight

    Board number: P/N: 37GU41000-10

    Obvious thing are: working cable and inverter and no damaged pins. Screen CCFL bulb is ok.

    Has anyone dealt with this sort of issue before? Any schematics available?

    Thanks.
    Full-time computer repair tech (10am - 6pm) and full-time, (8am - 11pm), Ruby on Rails Developer
    Tags: None
    • dj_ricoh
      Badcaps Legend
      • Jan 2013
      • 2073
      • uk
      #2
      Re: Advent 5611: No Backlight

      You check the input voltage of the inverter.
      If you got that means kbc does not enable the inverter
      Just cook it! It's already broken.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • triplefour
          UN65TU700DF picture and sound but no backlight. BL tests ok but repl. PSU didnt fix!
          by triplefour
          this tv is throwing me for a loop. do samsung tvs no longer have the backlight self test feature built into the power supply?
          i tested the backlight with my LED tester and it lights up both strips. one of them reads 100v and the other reads 63.7v.
          unplugged mainboard from power supply but left backlight plugged in, and then plugged psu wall power in. expected to see backlights light up but see nothing.
          according to how ive diagnosed in the past, this would almost always be a bad power supply. replacement power supply was cheap like 20$ from ebay. but still i get not even...
          09-13-2023, 10:43 PM
        • DanPoka
          Guide me through repairing a Dell p2210f LCD ccfl backlight monitor
          by DanPoka
          I bought this p2210f dell monitor to fix. Schematic is the same as p2210.
          Behaviour is that monitors comes on but then backlight switches off almost instantly. If I look with flashlight I can still find the "No signal message". So definitely a backlight issue. Trying to advance the issue I proved that the protection circuit is switching off the backlight by shorting out C3 and resistor to disable the INL chip then re enable by removing the short.
          This is where it gets interesting. When I disassembled the monitor to solder leads on c3 capacitor I noticed the backlight flickered...
          02-15-2025, 05:05 AM
        • repair-it
          TOSHIBA DLP 52HM95 How to reset timer module on bulb
          by repair-it
          I replaced the bulb only on my Toshiba DLP The bulb is a TB-25. This is the first time I've done a bulb only replacement. Supposedly there is a timer module that needs to be re-calibrated or reset. I don't know where the module is located. I see some vendors selling the bulb with the housing stating module included which leads me to think the module is located inside the enclosure the bulb mounts in, but I didn't see it. Maybe it's inside the plug attached to the bulb?

          Anyway - I am seeking information on how to reset this so called module so that the lamp will operate. Apparently...
          10-11-2023, 07:18 PM
        • Comp_Pro
          No Backlight Macbook A1990 820-01041
          by Comp_Pro
          Hello all,

          Am trying to figure out this backlight issue with this A1990 Macbook Pro.

          Tests performed:

          There is no backlight even with a good screen.
          Backlight IC is receiving the correct support voltages.
          Fuse F8400 ok
          Current sense resistor R8400 ok
          Backlight IC is receiving 3.3V on enable pin.
          Backlight IC receiving voltage from PPBUS_G3H, aprox 12.5V.
          Backlight IC receiving 5V from PP5V_G3S
          Backlight IC BKLT_SCL and BKLT_SDA both measure 0.545V diode mode to ground
          I2C_BKLT_SCL and I2C_BKLT_SDA both measure...
          05-06-2024, 10:23 PM
        • jimbofz
          lg 32LC46 backlight inverter board fault
          by jimbofz
          Hi this oldie had no backlight .after replacing caps on 24v rail ,
          still no b/l this uses inverter type:1315 B1-16A,
          im sure ive come across the same inverter in a samsung possibly le32r88bd ?
          all t/x in board test ok ,so i fitted 15k and led to pin 4 of oz964gn ic
          this allows protect to be temporary overridden.
          b/l now comes on
          but the left hand side of pic is gradually darker than the right side
          i have the cct for the tv
          but it does not have inverter cct.
          i opened it up to inspect the ccfl tubes
          and they dont have any...
          12-19-2021, 06:58 AM
        • Loading...
        • No more items.
        Working...