help,am i looking at the correct capacitors?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • baltog
    New Member
    • Oct 2012
    • 4
    • philippines

    #1

    help,am i looking at the correct capacitors?

    hey guys i just want to know if im looking at the coorrect capacitors. im just new oon laptoop repair. im going to remove these caps and put on my toshiba m200. if im not mistaken this are 330uf, i dont know if these are 2.5v. please help.. all replies will be greatly appreciated



    https://www.facebook.com/photo.php?f...4&l=5d9e24fc43
    Attached Files
    Last edited by Per Hansson; 05-25-2014, 12:17 PM. Reason: Offsite photo uploaded
  • Duncanbest
    Senior Member
    • Jul 2012
    • 81
    • Taiwan

    #2
    Re: help,am i looking at the correct capacitors?

    panasonic SP-CAP

    FYI

    https://www.badcaps.net/forum/showthread.php?t=26814


    330uf 2V

    Comment

    Related Topics

    Collapse

    • greystash
      How do I find the correct capacitors?
      by greystash
      I recently recapped my first computer (Power Mac 6100) and it seemed to go ok. After trying to boot it I get a crackly boot chime and then I hear the crash sound.

      How do I know if the replacement capacitors are suitable? (I am a total newbie and should have done a bit more research obviously)

      Original capacitors labelled:
      Y4 (I believe this is the batch number?)
      47
      16V

      On my other 6100 they are labelled:
      Small rectangle and then "4E"
      47
      16V

      Replacement capacitors: (aluminum polymer solid-electrolyte...
      10-18-2022, 06:24 PM
    • dragon3x
      After updating motherboard capacitors, what to do next (Asrock K7VT2, SOLTEK SL-75FRN2L)
      by dragon3x
      Hi, I have some 32 bits computer motherboards that need repair, as they fail to
      power on.

      Here are some examples :

      (N.B. "capacitors" indicated here are electrolytic capacitors located in the onboard
      switching supply area).
      (N.B. #2 : I could not find a 3300 microF aluminum-polymer with a higher voltage
      than 6.3 V.)

      1 - Motherboard #1 : this is an Asrock K7VT2 (socket A) that still works well. To put it on test
      I replaced capacitors with aluminum-polymer.
      3300 microF/6.3 V. x 4 replaced by 3300 microF/6.3 V. (KYOCERA...
      03-21-2025, 02:46 PM
    • slybunda
      AA and AAA battery charger capacitors?
      by slybunda
      hey all, iv got my favourite battery charger here which iv had for many years probably 15 years now or maybe even more. it still works good but thought id open it up to clean the dust out of it, lots of dust inside but now its clean and noticed 4 capacitors inside it and wondered if i should replace them.
      it has inside:
      2 x 47uf 16v caps 105c branded as Su'scon (lol sounds sus to me)
      2 x 470uf 16v LZ105c branded as G.Luxon

      not heard of these brands are they any good?

      iv attached photos of the charger and the board inside for an idea on the type of...
      12-24-2023, 04:41 AM
    • sam_sam_sam
      Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
      by sam_sam_sam
      I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

      This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

      After all of...
      07-13-2024, 08:14 PM
    • Ady2017
      Are there any datasheets available for Elna RJG capacitors?
      by Ady2017
      I have a 2007-era Panasonic VHS combo that is full of of Elna RJG capacitors. I am trying to test the capacitors to diagnose the machine and then select replacement capacitors but I can not find any datasheets for them. I did find a Elna catalogue from 2007-2008 but there is no mention of this capacitor series. Where these specially made for Panasonic and so not made available to the public? Any ideas what to find out what the ESR values should be without the datasheets? They are all between 10V and 50V and 47uF and 1800uF. None are leaking or bulged but I know that they need to be tested to be...
      05-25-2025, 02:19 PM
    • Loading...
    • No more items.
    Working...