PCH compatibility

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Beertimenow
    Member
    • Mar 2020
    • 21
    • United Kingdom

    #1

    PCH compatibility

    Hi I have SR40B damaged, can I replace with SR40E? or need to be B version?
  • kalilinux25
    Badcaps Legend
    • Mar 2018
    • 2084
    • ZAMBOANGA SIBUGAY

    #2
    Re: PCH compatibility

    Originally posted by Beertimenow
    Hi I have SR40B damaged, can I replace with SR40E? or need to be B version?
    Nope they are not backwward compatible

    Comment

    Related Topics

    Collapse

    • bembeno
      can i replace damaged 14n36gvl with 20n60 ?
      by bembeno
      can i replace damaged 14n36gvl with 20n60 ?
      01-30-2024, 09:39 AM
    • XxMicroSoldering
      ASUS Rog Strix G17-712LV Laptop Liquid damaged
      by XxMicroSoldering
      Hello Guys

      I have a ASUS Rog strix laptop that I bought recently to fix and the previous owner spilled water on it . He brought it into a repair shop for them to check it out and instead of fixing it they damaged the battery connector of the laptop ! Other than that they damaged damaged nothing . But since the liquid damage the laptop only turns on and the keyboard lights up and then immediately turns off. I really want to repair this laptop and I also have experience in repairing phones etc and laptops and a bit of soldering but the diagnosing part is where I need help with and...
      10-17-2024, 10:45 AM
    • ferah831208
      Strange battery present behaviour in Lenovo Legion 5-15ARH05 mb model nm-d041
      by ferah831208
      Hello guys, i need help with this problem, I have a NM-D041 mobo, it came with low impedance in 3v linear regulator rail, the cause was a damaged EC controller ITE8227e-192. I ordered a new one and replaced it. This laptop have a different chip for keyboard management and it8227e pins for programming ITE chips are not accesible through keyboard interface, I flashed it using i2c interface pins with vertyanov programmer because laptop was dead and SPI flash didn't have power (only 3v EC) so it couldn't access firmware stored in SPI memory. I read SPI and extracted it8227 firmware from original BIOS...
      03-18-2025, 01:18 AM
    • Tomylee
      Identification of Component T5 on NEXIQ USB-Link 2 (damaged due to crushing)
      by Tomylee
      Hi everyone,
      I'm currently repairing a NEXIQ USB-Link 2 that was physically damaged due to crushing. After a thorough inspection, it appears that only one component is visibly damaged: the T5 component, located right next to the Mini-USB port.

      It's a 4-pin SMD component, with one pin at each corner, aligned front-to-back along the USB port axis. Unfortunately, it is broken, and there are no visible markings left on the part to identify it.

      I'm looking for help with the following:

      The exact identification or part number of the T5 component
      ...
      05-28-2025, 12:42 PM
    • acedogblast
      Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
      by acedogblast
      This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

      There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
      11-02-2024, 05:13 PM
    • Loading...
    • No more items.
    Working...