Generic in-dash navigation system AAOGP300194/365125
This unit runs on Windows Embedded CE 6.0 Core, and I am looking for pinouts of each connector.
Attached Files
-
My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics. -
Re: Generic in-dash navigation system AAOGP300194/365125
did you search the "mast" number, or power it up to see if there is a splash-screen with a makers name? -
Re: Generic in-dash navigation system AAOGP300194/365125
It looks similar to this: https://www.myturbodiesel.com/d2/100...10-swap-vw.htm Could be from a VWAttached FilesLast edited by R_J; 03-14-2021, 06:51 PM.Comment
-
-
Re: Generic in-dash navigation system AAOGP300194/365125
This was enough info for me to power up this unit - the boot screen is "Opal" and the home screen has the Volkswagen logo; the navigation software is NaviOne with the OS being PRIMA-v1.53 (the unit has a bad SD card for navigation).
But I still wonder why the unit had generic branding on the labels in the first place (possibly an aftermarket replacement?).My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.Comment
-
Re: Generic in-dash navigation system AAOGP300194/365125
https://www.ebay.com.au/itm/HOLDEN-C...p2047675.l2557Comment
-
Re: Generic in-dash navigation system AAOGP300194/365125
Hi, further to this thread, I picked up (literally from the side of the road) a similar double DIN in dash DVD player with GPS - which looks unused. However, the rear plugs are different to the other '365125' unit in this thread. Does anyone recognise this particular unit? I'd love to power it up if I can get the pin-outs :-) Thanks in advance brains trust.Attached FilesComment
-
-
Re: Generic in-dash navigation system AAOGP300194/365125
Obviously these units go under the name of Opal, does anyone know of any links to the manufacturer for more info?Comment
-
I know this is old stuff but I have the wires here ( can send pics ) if you need them as I am trying to fix it from my daughter's car, or waste it goes.Comment
-
also have the manualComment
-
I already posted this on vogons.
Its a 3d printed custom bracket for socket 478.
I used this AM4 bracket as a base design.
Its to be use with cheap generic clip based cpu cooler.
Reason for doing this is:
- Its hard to get/find a good copper base cooler. Even if you find one, the price is ....
- New generic cooler is cheaper and can use bigger fan (less noise)
I tested the bracket with cheap chinese horizontal cooler + fan taken from CM hyper 212 evo.
The processor that I was using is P4 2.4Ghz prescott.... -
Good evening I am working on a Reebok oneGT40s treadmill. It had a flashing display which the replacement of D3 rectified. However the lift motor now runs when the mains is turned on and does not stop. If I then select start so the tread motor runs and disconnect the up lead to the lift motor it stops. If I then reconnect the lead the lift motor works as it should with the controls. It will continue to work correctly until the mains is turned off and on again, or the safety device is removed and replaced. It then runs again and only by disconnecting and reconnecting the up lead will it operate...
-
Would somebody PLEASE have pinout for any of these 3 chips: Sigma Designs (Coppergate) CG2313QIR-00 (QFN-64) and CG3215QIR-00 (QFN-128), as well as Marvell 88E6020-NNC2 (QFN-64)? I tried everywhere I could think of on the internet without success. You can buy them alright, although not at any of the major distributors - mostly eBay, but I can't find any datasheets or at least pinouts. How one is supposed to design anything without such a basic information like chip pinout? Not even mentioning any more detailed properties... These integrated circuits are used in EOP (Ethernet Over Power) and POE... -
Hi, i have this iMac issue
I've checked temperature by using macfans with no results
techtool pro shows me AMBIENT AIR TEMP FAULT
i'm going crazy, the mac runs very slowly
where i can find this sensor on motherboard?
thanks in advance
... -
Generic CopyDMI Scripts to complement the Experienced Copy DMI guide:
Copy DMI info easily with Hex editing software and Macro script
https://www.badcaps.net/forum/showthread.php?p=1214739
Tiny Hexer - https://www.softpedia.com/get/Others...ny-hexer.shtml
Post your generic scripts in this thread, no bios requests or any other questions , just scripts that everyone can use for any bios with the same *DMI off-sets. Posting a thank you is ok though,if you find what everyone posts useful.
The scripts can be named anything you want...
Comment