That would have been perfect for G31-M4 if not for the 95W tdp limitation.
Its VRM mosfet is nikos P0903BDL and P0603BDL.
Its hard to find cheap S478 64-bit P4. The current price is
Its understandable since its very rare....
BleedCap
Member
Last Activity: 03-21-2024, 12:05 AM
Joined: 08-24-2015
Location: KB
-
Re: OLD Socket 478 custom bracket + NEW generic cooler
That would have been perfect for G31-M4 if not for the 95W tdp limitation.
Its VRM mosfet is nikos P0903BDL and P0603BDL.
Its hard to find cheap S478 64-bit P4. The current price is
Its understandable since its very rare.... -
Re: OLD Socket 478 custom bracket + NEW generic cooler
That blue motherboard (Acorp 4PMMNL) is for testing and using for hotswap bios flashing (5v only plcc32).
It used to be faulty, keep beeping asking for ram. Replaced the faulty mosfet APM2055N with FDD8870 taken from dead P4M900-M4, problem solved...
or not
It got a main problem, high side mosfets (I think) is very hot heating the surrounding area. Already replaced the mosfets, still the same.
Probably vrm driver ic (5093MTC 2Phase) problem or maybe its normal for that motherboard, I dunno....Leave a comment:
-
Re: OLD Socket 478 custom bracket + NEW generic cooler
ABS.
Yes, PLA probably won't more so if using prescott....Leave a comment:
-
Re: OLD Socket 478 custom bracket + NEW generic cooler
I haven't try in the case yet, but I can't think of any reason for it not to fit except fot that horizontal cooler + 140mm fan. Vertical tower cooler should be fine....Leave a comment:
-
Re: OLD Socket 478 custom bracket + NEW generic cooler
bonus pictures...Leave a comment:
-
OLD Socket 478 custom bracket + NEW generic cooler
I already posted this on vogons.
Its a 3d printed custom bracket for socket 478.
I used [URL="https://www.thingiverse.com/thing:2681174"]this[/URL] AM4 bracket as a base design.
Its to be use with cheap generic clip based cpu cooler.
Reason for doing this is:
- Its hard to get/find a good copper base cooler. Even if you find one, the price is ....
- New generic cooler is [B]cheaper[/B] and can use bigger fan (less noise)
I tested the bracket with cheap chinese horizontal cooler + fan taken from CM hyper... -
Re: Biostar TH55B HD (@IH55E-MHT) Schematic/boardview
Thank you very much kind sir.
...
Leave a comment:
-
Biostar TH55B HD (@IH55E-MHT) Schematic/boardview
I'm in need of schematic or boardview for this motherboard please.
I don't have access to other sites that have the schematic.
In case anyone here got it and willing to share.
Thank you.
-
Re: Need Lenovo S110 schematics BM5138 rev 1.3
Thanks you.
Leave a comment:
-
Re: Laptop Motherboard Schematic Diagram 2017
Thank you...
Leave a comment:
-
Re: Toshiba Satellite - Locks up when plugged in
I got Acer 6920g that wont post.
Can I replace nec tokin with polymer cap like from desktop motherboard as a replacement?
Not permanently, just as a test before I get the tantalum.
...Leave a comment:
-
Re: w2346t-bf LCD: Retrofit LED Strip Kit
Can you give the link, cannot find it.
...
Leave a comment:
-
Re: Need help repair dead AVF brand power supply
Congratulation
I have a question.
Can the coil/inductor from motherboard be used?
[ATTACH]121812[/ATTACH]...Leave a comment:
-
Re: ECS RX780M-A no POST
That 16v polymer caps is Lelon.
Leave a comment:
-
Re: Need help repair dead AVF brand power supply
More like for cost cutting.
...
Leave a comment:
-
Re: wall wart: bad caps strikes again!
[url]http://capacitor.web.fc2.com/s_other.html#s2[/url]Re: wall wart: bad caps strikes agai....html#s2[/url]Leave a comment:
-
Re: Fake primary capacitors
Yes, Cooler Master 430W (RS-430-PMSR) made by Hipro (HP-D3057F3R).Leave a comment:
-
Re: Fake primary capacitors
Thanks for the offer, I'll think about it.
I'm in no hurry for it though.
I have the same old dead PSU like this one
[url]https://www.badcaps.net/forum/showthread.php?t=20722[/url]
Its damn heavy.
And it served me well for 5 years.
Re: Fake primary capacitors<br />
<...22[/url]<br />
Leave a comment:
-
Re: Fake primary capacitors
[URL="http://www.ebay.com/itm/4-Pcs-of-NCC-KZE-Series-16V-2200UF-Ultra-Low-impedance-Made-in-Japan-Capacitor-/301691419419?hash=item463e35bb1b"]NCC KZE 16V 2200UF 10x25[/URL]
Is this capacitor real?
That size doesn't exist in the KZE datasheet.
I'm searching a replacement for Teapo SC 16v 2200uf (10x30).
Its for my PSU, cannot fit 12.5
Re: Fake primary capacitors
[URL="http://www.ebay.com/itm/4-Pcs-of-NCC-KZE-Series-16V-2200UF-Ultra-Low-impedance-Made-in-Japan-Capacitor-/301691419419?hash=item463e35bb1b"]NCCLast edited by BleedCap; 10-06-2015, 03:27 AM.Leave a comment:
-
Re: MSI 945GCM5 V2 Full Poly-mod
Thank you for the feedback. Actually I already know that you can use lower uF poly caps in the VRM side, but I still cannot find about replacing higher uF poly caps other than VRM.
Yes it's a waste of money. But should there be a situation for example where I don't have lower uF poly to use only a higher uF available, can I still use it?
It's just a hypothetical question for a reference in the future.
VRM (CPU/RAM):
Lower uF poly replacing higher uF lytic = OK
Other...Leave a comment:
No activity results to display
Leave a comment: