hi guys..
need some help pls.
What pinout is enable in this ic?
regards
need some help pls.
What pinout is enable in this ic?
regards
-
-
Re: it8772e enable pinout?
https://datasheetspdf.com/pdf-file/1.../ITE/IT8772E/1
Whats the motherboard you`re working on , make/model -
Re: it8772e enable pinout?
first ite check 12v if ok
then check 5v
after that chech 5volt standby ,3.3 volt standby
after all voltage ok .pson signal send to h61 chip
if search youtube /find that
before do anything. check 5,12 5volt sb ,and dc to dc convertor "5=>3.3 sb"
may be some capacitor is shortedComment
-
Hello. I have an Inspiron 7501 here, it's the same as a Vostro 7500 in some markets (no clue). I was looking to replace the LCD, the panels included with these models are terrible.
I have the schematic and it is a 4 lane eDP port on the board but the pinout seems quite weird, my question is if anyone recognises this weird pinout and knows of any other Dell models that may use it or even any compatible panel models. I have the 40-40pin cable that was used for the models with touch but do not need touch capability, was just looking for a better quality screen and higher refresh to actually...10-02-2024, 04:54 PM -
Sub: Missing enable on +5v sec pwr rail AMD Firepro D500-B/Mac Pro late 2013
Ref: 1/ MacPro6,1 Late 2013/A1481 MD878LL/A (3.5 GHz 6 Core Xeon E5-1650v2)
Gfx-B: APN: 661-7548 PPN: 820-3533-A AMD FirePro D500-B 3GB Vmem
2/ Figure 1 Gfx-D500-B Front Facing
3/ Figure 2 +5v supply (zoom-in)
Intro:
While troubleshooting a Mac Pro(6,1) referenced above I discovered the +5v secondary supply did not stand up on the D500-B graphics card as a result of a missing enable signal. The +3.3v secondary rail was the only rail that did standup. I tried to perform...12-07-2023, 09:55 PM -
The LCD on my Korg KROSS2 keyboard is cracked and needs to be replaced.
However, the cost of a replacement LCD is almost the same as the price of a second hand Korg KROSS!
Does anyone have a copy of Korg KROSS2 Service Manual? I want to see the PINOUT for the LCD connection. Perhaps I can find a compatible LCD screen and not have to spend a fortune on an original replacement LCD.
From what I can gather, the LCD screen is a COG with serial interface (SPI). Is there any way I can ascertain (perhaps with the use of a multimeter or oscilloscope) the PINOUT by... -
For those that have worked through the 7290 BIOS in the past, do you happen to know if there is a switch in it to enable a touchscreen entry in the BIOS setup?
The 7290, 7390, and 7490 all use the same BIOS, and the 7390 has an FHD touchscreen as one of its' options. It turns out it can be installed in a 7290 BUT since the BIOS doesn't have the entry to turn it on, it just becomes an FHD upgrade to the 7290.
I was hoping if any of you that had worked on the BIOS in the past would know if either the touchscreen settings could be turned on in the 7290, or the BIOS could... -
Hi,
I came across with
SAMSUNG UE65HU8500
ONE CONNECT BN41-02135
Chassis GOLF_UHD_1MP_JACK
TV can not recognise ONE CONNECT box, so I need to know the pinout of the CN 3301 connector.
Moreover, on the main is written A5V. However, cable connected this pin to the GND.
Maybe somebody have an experience with the same issues?
I need your help.
Thank you....
Comment