Resurrected 694D Pro-AR

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • s0lid
    Member
    • Jul 2009
    • 14

    #1

    Resurrected 694D Pro-AR

    Well i got this board earlier this year for free and now i decided to recap it.

    Well every cap with greater capacitance than 470uF got replaced with 1500uF 6.3V Panasonic low ESR caps, works greatly now

    I think they should do fine even they might be have even twice lower specs that earliers had. Usually on mobos very low ESR is more needed that high capacitance, but that's what i've heard.

    Currently installing WinXP and i can post pics later.
    Last edited by s0lid; 07-14-2009, 08:49 AM.
    Same s0lid from XS and 2cpu forums.

Related Topics

Collapse

  • Junkrepair
    Calculating ESR from tan delta -- tan delta's dependence on capacitance
    by Junkrepair
    I'm finally recapping my Soyo K7VX6 motherboard (aka KT600 Dragon Ultra) and replacing Sacon SZ-series caps. The Sacon SZ datasheet provides a spec for tan delta, but not for ESR, while the candidate replacement caps are specified in terms of ESR.

    I found this nice little description of the conversion:

    Calculating capacitor ESR from Tan(delta)
    https://forum.digikey.com/t/calculat...-from-tan/2633

    It mentions that a general spec for tan delta has to be adjusted for the specific capacitance before plugging tan delta into the formula...
    06-12-2023, 02:45 PM
  • Sparklingx
    SMD ceramic capacitor capacitance & voltage
    by Sparklingx
    what is the easiest way to measure the capacitance of SMD ceramic capacitors and its rated voltage?...
    09-12-2024, 01:04 AM
  • Antonynl
    Capacitance and voltage of tantalum?
    by Antonynl
    I have a tantalum capacitors with indicators EB 21 that measures only 22pF. See attached picture.

    Since this is a windmeter that is normally in a very high mast I would like to get the correct replacement capacitor.

    Is there somebody that can tell me what the capacitance and voltage of this capacitor are?

    I don't feel confident that I can figure this out myself after searching around

    Cheers!!
    04-14-2024, 03:19 PM
  • SwedishDiesel
    Dell Optiplex GX260 - Advice Needed for Polymodding Motherboard
    by SwedishDiesel
    Howdy folks,

    I have an Optiplex GX260 that blew a couple of those troublesome Nichicon HM series (ultra low ESR) electrolytic capacitors. Because said caps are obsolete, they are pretty much impossible to find on the market; I did find a listing for some but I believe they are counterfeit. I feel the easiest thing to do would be to replace all the blown caps with polymer ones. I am by no means an expert in electronics, and I've found a fair bit of conflicting information, so any guidance or confirmation would be greatly appreciated. While from a practical standpoint it's not worth...
    10-30-2021, 12:47 AM
  • Aetherone
    Blast from the past #2: MSI 694D-Pro A ver:1.0
    by Aetherone
    With the success of my Asus A8N32-SLI Deluxe recap project, I'm turning my attention to the other benchmark board in my history - the venerable MSI 694D-Pro A.

    Wayyyyyy back in the day, I paired one of these (in protoype orange PCB no less) with a pair of 366 Celerons for a world of fun. That board was flawless from day #1 (well, aside from the usual VIA issues with sound cards and Promise getting narky about additional HDD controllers). Wish I'd never sold it off.

    The current board is one of a hundred examples from a teaching college near the IT shop I used...
    01-15-2019, 10:32 AM
  • Loading...
  • No more items.
Working...