P5n32E-sli plus

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bigfoot18
    New Member
    • Jan 2009
    • 2

    #1

    P5n32E-sli plus

    I need to replace one of the capacitors that fell off the motherboard. They look like whats in the picture at http://www.pcstats.com/articleimages...sliplus_m1.jpg. The one that I need to replace is 711, 471, 6.3v. Any help is appreaciated. thank you
  • gdement
    Badcaps Veteran
    • Jan 2007
    • 690

    #2
    Re: P5n32E-sli plus

    I'm not sure of the manufacturer or how they do their markings, so I could be off the mark here.

    But most likely:
    471 probably means 470uF (47 are the significant digits, 1 is the number of zeroes to append).
    711 is probably a manufacturing date code.

    Can't be sure what to replace it with without knowing the brand and series. But if I had to guess I'd look up that size (470uF 6.3v) in United Chemicon PSA series sold at digikey. Those are very high end caps so they'll probably do fine.

    Comment

    • kc8adu
      Super Moderator
      • Nov 2003
      • 8832
      • U.S.A!

      #3
      Re: P5n32E-sli plus

      fujitsu re solid polymer.ncc psa will work too and can get at digikey.
      470@6.3v
      note the f logo.

      Comment

      • Wizard
        Badcaps Legend
        • Mar 2008
        • 2296

        #4
        Re: P5n32E-sli plus

        Yes, Fujitsu.

        And yes again, 470uF 6.3V polymer. How on earth this can fall out? This is through hole solder unless your board is using SMT capacitors.

        Comment

        • bigfoot18
          New Member
          • Jan 2009
          • 2

          #5
          Re: P5n32E-sli plus

          Thanks for all the info. I will try to order some from digikey.
          As for the cap falling off, it looks like some one knocked it off when taking the heatsink off. The dimm slot latch closest to the cap is also broken.
          I'm hoping that the cap is the only major thing broken.

          Comment

          Related Topics

          Collapse

          • chth96
            Is it no harm to replace with capacitor without ripple current rating?
            by chth96
            When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


            Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
            But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
            Rubycon YK DataSheet (b...
            04-19-2024, 05:19 AM
          • RetroComputingGrotto
            Opinions/Advice on Do/Should I replace ALL Electrolytic Capacitors on old equipment?
            by RetroComputingGrotto
            I've just been repairing some (very) old speakers with a loud hum that occurred as soon as you powered them on regardless if any actual audio is played through them. I work in a School so it's 99% likey that the Teachers have hardly ever turned the power off on them for well over 10+ years.



            As you can see the top large capacitor on the right has a bulge on the top so defincately needs replacing. As the one next to it is exactly the same capacity and voltage I planned to replace them both.


            What is your advice/opinion on whether or not on old(er)...
            04-03-2024, 08:30 AM
          • chth96
            Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
            by chth96
            I have purchased an 100-240v AC/5v 2a DC adaptor from aliexpress,and a month ago It smelled burning when I plugin it powerstrip.
            Since then, This AC/DC adaptor have been out of order.
            But A few days ago,I replace 0.5 watt resistor with 1 watt resistor(1ohm) in this adapter.
            After replacing resistor,It succeed to recharge all of android phone.And When I measure voltage on the two pins of USB port,It shows 5.5v
            Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
            And Is there any possibility that it will suddenly explode as well as to be out...
            12-03-2023, 04:40 AM
          • psyduck
            Conformal coating on Samsung U32D970 monitor PSU, do I need to replace after repair?
            by psyduck
            I have a Samsung U32D970 monitor from 2015 I pulled out of the bad hardware pile that turned on and then turned itself back off after a few minutes of use and refused to turn back on. The PSU has part number BN44-00786A, and I found a couple posts about one that had blown with damage to the MOSFETs and PWM controller - but nothing about intermittent failures. I started a new thread and said that I would refresh the solder joints on the board to see if it was just a bad connection and possibly replace the PWM and PFC ICs. I then asked what my next course of action would be after those steps. I...
            11-27-2023, 06:56 PM
          • disorder
            HP 2311 display, 3.3v regulator fried, need help to replace
            by disorder
            hello,

            i have a hp display 2311 to repair, totaly dead
            on the board, il have 2 capacitor 470µf that are dead and the 3.3v regulator : ax6630-33
            i have no such regulator, can i replace this one with a mic5209-33 (3.3v outpout regulator too) ?

            thank you
            Yesterday, 04:34 AM
          • Loading...
          • No more items.
          Working...