DFI Lanparty B / Ultra Infinity (nF2)

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • gustie
    Senior Member
    • Dec 2008
    • 76
    #21
    Re: DFI Lanparty B / Ultra Infinity (nF2)

    I checked my CAPS

    my LP NF2 Ultra B is made in Taiwan REV A - it has green TEAPO caps and the others i cant read properly....

    none look bulged - done a few pics below...







    i noticed in front of the AGP slot a small cap that looks like it has been hit maybe? its not sat flush...


    also here is my GFX card caps - EVERCON??



    TEAPO are PAP then? they all look ok so far except that small one which is bent.... could this be a problem??

    thanks

    DFI Lanparty NF2 Ultra B
    TICTAC 619XT Bios
    AMD Athlon XP-M 2600+ FQQ4C IDYHA I-Stepping
    Speeze Vulture spin 3 Heatsink and Fan
    2x Mushkin XP4000 1024m DDR500 (1:1) @ 2.5-3-2-8 1T
    GeForce FX 5700 256m
    Zalman VF900 CU GPU cooler
    Skyhawk 400W Aluminium psu
    Sharkoon Silent Eagle 1000 case fans

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • vlady carp
        Looking for Dump for P87C51SBPN (Concord Infinity Elevator)
        by vlady carp
        Hello, colleagues!

        I'm currently dealing with an issue while repairing a Concord Infinity elevator. The microcontroller P87C51SBPN used in the control board has failed, and I need the original firmware dump in .bin format to replace it with a new processor.

        What I've done so far:
        • Diagnosed the issue and confirmed the microcontroller is the root cause of the problem.
        • The original processor is beyond repair, and I wasn't able to extract the dump.
        • Reached out to the manufacturer (Savaria/Concord), but I haven't received a response yet.
        ...
        1 Photo
        01-16-2025, 02:08 AM
      • ChaosLegionnaire
        what i went through dealing with my mobo with dead onboard sound!
        by ChaosLegionnaire
        so i took out one of my spare gigabyte ep35-ds3r mobos from storage for use to do some cpu, ram and video card testing of stuff i bought from ebay and got for free from momaka. he bought 50 e8400 cpus for cheap from ebay some years ago and i decided to help him relieve him of some of his supply since he had waaaay too many!! what did we say about hoarding too much stuff and depriving others of them?! *cough* socialism *cough* lol!

        i had to blow some dust off the board and heatsinks with the datavac as i didnt clean it up before putting it in storage. after finishing...
        09-13-2022, 09:02 AM
      • Cerberuska
        Mobo MSI B550-A PRO password popup
        by Cerberuska
        Hello guys,
        I have interesting problem. My MoBo MSI running on Ryzen 7 w/o graphics just good. I swapped to Ryzen 5 5600G and on the boot I stuck with screen on picture. Enter Password. I checked BIOS setting with Ryzen 7, no security is enabled, BIOS password or TPM.
        BIOS I updated to last one.
        any suggestions?
        And same thing for two different 5600G, and yes, MoBo supposed to support it.
        Thank you...
        1 Photo
        11-10-2024, 01:23 PM
      • mrsith
        Dell G3 17 3779 - no display after mobo replacement
        by mrsith
        Hi guys,

        I have a friend's Dell 3779 that came to me with severely shorted mobo. Did not manage to isolate the cause, most likely that was a bga shorted. Went for a replacement motherboard. Got one from China, apparently it's been tested prior to shipping. The mobo starts up normally but I am getting no display whatsoever.

        Tried using external monitor, but being blind I am not sure if laptops goes as far as booting to Windows, a d without it I cannot get hdmi to work. Can't see boot menu options to make sure it boots to Windows. Went ahead and did a blind bios update,...
        04-30-2023, 05:11 AM
      • Ibod
        Corsair cx600 psu & ASRock B450Pro4 mobo wont start
        by Ibod
        HI I have a PC using a Corsair cx600 psu & ASRock B450 Pro4 mother board that won't power on after a shutdown (replaced a dead drive in a raid array) Not the boot drive.

        With most things unplugged, including the 24 pin ATX connector, but not the ATX12v to cpu, I have +5.01V on the +5vsb pin 9 from the PSU. When I plug the 24 pin back in to the mobo, the +5vsb fluctuates between 1.1v & 1.9v.

        Not sure where to go from here ?

        Is the PSU at fault or is the mobo causing the problem

        Look forward to any help :-)

        If I plug the 24...
        02-08-2023, 11:00 AM
      • Loading...
      • No more items.
      Working...