Pioneer HM82 - No power

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • andrew1701
    New Member
    • Sep 2020
    • 2
    • UK
    #21
    Re: Pioneer HM82 - No power

    Hi in order to get into the service menu you need Service remote control unit GGF1381, not the unit the came with the system

    BR

    Andrew

    found one here:

    https://www.remote-control-world.eu/...SABEgJBQfD_BwE

      Comment

      • Andrew453
        New Member
        • Jul 2020
        • 4
        • England
        #22
        Re: Pioneer HM82 - No power

        Thanks Andrew.

        I've taken a guess that it's probably the ICE3BR0665J - SMPS Current Mode Controller. The blue flashing light is the protection mode, when it detects an abnormal power supply condition.

        No idea whether it is that component, but only a few Β£ to buy one so I'll swap it out when I get a moment.

        Andrew

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • dkneyle
            Onkyo DX-V500 Laser Disc Player - weird SMPS fault
            by dkneyle
            This relic from a technology path that came to a dead end (but still has historical interest) was brought in with a dead SMPS, which is based around a MK1210 device. I got it going after a battle. It seems to have a strange design - if it's not getting feedback that the secondary is OK it cause the big FET to go into full conduction and overloads resulting in a blown fuse at best or something worse! I'm using a Dim Bulb Tester (70W/230V) which thankfully has saved the day a number of times whilst repairing.

            Now, it loads a CD OK. The motor voltage output (which is built onto the SMPS...
            02-01-2022, 02:08 AM
          • shamsudeen
            Hi, Can we use SMPS Bench Power Supply for Laptop troubleshooting?
            by shamsudeen
            Hi all, I just need to know that, can i use SMPS type power supply to test and short circuit detection on a laptop motherboard?
            I saw 95% of repair guys are using only Linear bench power supply. linear bench power supply is pricy, thats why i planned to get one SMPS supply.

            i know that in linear power supply the noise will be very low comparing to SMPS supply....
            07-19-2025, 07:14 AM
          • gabri2211
            external hd Seagate, broken down the +12 volt and USB 3.0 SATA board
            by gabri2211
            Hi to all 😎
            I'm looking for any useful information to repair this interface (I have attached the image).
            On this board I read E3215-1215A_4D.
            This is the small plate inside the HD enclosure that allows to connect a 12 volt power supply, interface the disk with a USB 3.0 socket and is connected to the HD with the SATA connector.

            If any of you have found a burnt or short-circuited component in a circuit like mine​, if you have useful diagrams for the repair, or even better a description for the tests at the test points, I would be very grateful.
            in particular...
            1 Photo
            11-12-2024, 08:08 PM
          • Bushcat
            Pioneer PL-X9 motor speed control wobble
            by Bushcat
            I'm starting to re-cap a Pioneer PL-X9 turntable, specifically the motor control board, because although everything tests out OK according to the service manual, the speed wavers slightly despite the quartz lock light remaining on. So, I've decided to re-cap that board since it's the cheapest next step...

            Pioneer's passive component naming convention is clear to me. For example, CSZA R22M 35 is tantalum, radial leads, 0.22uF, 20%, 35V.

            BUT there are two capacitors on the board which have actual Pioneer part numbers: PCL-042. I can tell they are 0.1uF, 16V but don't...
            05-24-2023, 03:36 AM
          • EduCabral
            [Help Needed] Yatour YT-M06 (Pioneer 1) – Firmware or Schematic Request
            by EduCabral
            Hi everyone,

            I'm currently working on reviving a Yatour YT-M06 CD Changer Emulator module for use with a Pioneer 1 interface (specifically with a DEH-P5950IB head unit).

            While the unit is recognized as a CD changer, none of the USB, SD, or AUX features respond, which leads me to believe the firmware may be corrupted or incompatible.

            πŸ”§ Details:
            • Model: YT-M06
            • Interface: Pioneer 1
            • MCU: Fujitsu MB89F202
            • Goal: Find a valid .bin firmware file or memory dump from a working unit

            I'm happy to attempt flashing, analyzing memory dumps, or doing hardware-level...
            07-15-2025, 12:26 AM
          • Loading...
          • No more items.
          Working...