What do I need??

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • stevo1210
    Badcaps Legend
    • Oct 2006
    • 4156
    • Australia
    #21
    Re: What do I need??

    Originally posted by Spyke
    Yeah, its 12V, same thing as the "On" voltage.

    A lot of models power the low power electronics section with the "Always On" voltage. This almost always includes the display controller as well.
    I know it's been a long time and I have actually bought a proper stereo, but curiosity killed the cat and I decided to connect the 12V cables from my PSU to the "battery" and +12 in terminals and the display came on so I'm pretty happy that the unit works. Now I think this will be one of those "fun" projects for the weekend.

    Thanks.
    Don't find love, let love find you. That's why its called falling in love, because you don't force yourself to fall, you just fall. - Anonymous

      Comment

      • stevo1210
        Badcaps Legend
        • Oct 2006
        • 4156
        • Australia
        #22
        Re: What do I need??

        Soldered in all the required cables today and I'm happy to say that it's all up and running now.
        Don't find love, let love find you. That's why its called falling in love, because you don't force yourself to fall, you just fall. - Anonymous

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • domix
            LG Air Conditioner AC unit bypass
            by domix
            Hello,
            i have Lg AC indoor unit connected to heatpump warm water. To flow thru unit. I have it to heating up garage. I have previus old indoor ac unit. It was only connected to power supply and is was woking.

            Now i have new one which has a problem, it needs outdoor unit. It has error, 5 blinks which means that outdoor unit is not connected.

            how can i bypass this :/

            I need only to turn on and i need only fan to blow, and adjust speed od fan. To blow over a warm pipes....
            2 Photos
            11-25-2025, 02:54 PM
          • nzphil
            Yamaha YST-C10 stereo capstans run for 10 min when unit is turned on
            by nzphil
            I have a Yamaha YST-C10 mini-stereo that was made around 1990. It has two cassette decks, a CD player and an AM/FM tuner. When it is turned on in tuner mode, the cassette deck capstans normally run for about one second and then the radio will begin to play. Currently, however, the capstans run continuously for about five minutes followed by running intermittently in two second bursts for another five minutes. The radio will play softly when the capstans stop during the intermittent phase. After about 10 minutes of this, the capstans stop completely and all the stereo functions work fine.
            ...
            04-11-2021, 05:58 PM
          • ngml
            Repair of an LG split AC system indoor unit PCB
            by ngml
            I am trying to repair an LG split AC indoor unit, which does not start and gives a CH05 error code.
            This indicates an error in the communication between the outdoor and the indoor unit.
            The outdoor unit is fine, so the problem is the indoor PCB.
            The indoor unit is an LG PC09SQ NSJ (3SNM09JA2FA), and the PCB has the following type number: EAX35907219-1.2 (see photo1)
            I changed optocouplers ICO1X & ICO2X and the NPN transistor S9013 which drives optocoupler ICO2X (see photo2), but this did not remedy the fault.

            Does anybody have the schematics of this board,...
            2 Photos
            02-01-2025, 12:55 PM
          • CoinCoin88
            Garage door RX unit (Cardin S38C) does not short relay to send opening signal
            by CoinCoin88
            Hello everyone,

            I'm turning to the Badcaps community to help me troubleshoot the radio Rx card from my (old) garage door opener. While I could just ditch that card and replace the whole system, I first would like to understand "why" it suddenly stopped working, because that's just how I am wired...!

            Some basics: the receiver works on a 30.875 Mhz frequency. Yes, I'm aware this is not in use anymore in a looot of places. It does not use any rolling code, it's just a regular dip-switch code that you have to set up on both the receiver and transmitter. The receiver...
            09-15-2025, 03:36 AM
          • nobbnobb1
            Bose Companion 5 - Unit Powers On then Cuts Off Shortly After
            by nobbnobb1
            Hi guys,

            Trying to salvage a Bose Companion 5 computer speaker system that powers off shortly after powering on. It's got a primary USB input (built in DAC) and an aux 3.5mm input. The USB appears to be the primarily source that tells the unit to power on (control pod LED goes green) as the unit has no power switch.

            When I first connect power to the unit, plug in the USB, it will play audio nicely for a minute before it drops out and the unit appears to go into standby (control pod LED goes red). It stays in standby and I cannot seem to power it back on without physically...
            02-03-2022, 11:14 AM
          • Loading...
          • No more items.
          Working...