Onkyo tx-sr606 fluorescent display not working

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • redwire
    Badcaps Legend
    • Dec 2010
    • 3906
    • Canada

    #21
    Re: Onkyo tx-sr606 fluorescent display not working

    -VP is a 37VDC regulator Q9001 maybe check C9005, C9001 for heat damage. It makes +5VDIS and -VP at -31.5VDC
    Filament AC FLAC1, FLAC2 lines go through many connectors and just jumper in and out of a board. What a mess. They go to a transformer winding S4.

    Only 3 models get the cooling fans

    Onkyo TX-SR606 Service Manual here:

    Comment

    • assenheimer
      New Member
      • Aug 2023
      • 4
      • Brazil

      #22
      Re: Onkyo tx-sr606 fluorescent display not working

      Originally posted by lotas
      Replace the display power capacitors (anode voltage and filament voltage).
      So there is a hope!
      Did you know where I can find them on the board?

      Sorry for my poor English.

      Comment

      • assenheimer
        New Member
        • Aug 2023
        • 4
        • Brazil

        #23
        Re: Onkyo tx-sr606 fluorescent display not working

        So I replace the 470uf capacitor and success!!
        Thanks for the help!
        I'm so happy!

        Comment

        • redwire
          Badcaps Legend
          • Dec 2010
          • 3906
          • Canada

          #24
          Re: Onkyo tx-sr606 fluorescent display not working

          I'm guessing that is C9001 470uF 63V on the Video PC Board, schematic #4 SD-4.

          Comment

          • Blue95
            New Member
            • Oct 2023
            • 1
            • Australia

            #25
            Re: Onkyo tx-sr606 fluorescent display not working

            Had success today with one of these, thankyou

            Comment

            Related Topics

            Collapse

            • ai.need.help
              Onkyo TX-8050 AV-Receiver no sound
              by ai.need.help
              Hello,

              I have a problem with my Onkyo TX-8050 Receiver. I got it from aftermarket and it was just delivered today.

              It doesn't play music. There is no real output from:
              pre-out
              amp-out A and B
              phones out

              The only real sound I hear is a humming from the speakers when I play a song from usb or select a analog source. And when stopping and starting songs from usb or switching sources, I hear a crack from the speakers.

              I tested with analog-input, usb and radio.

              I know that there is a common problem with...
              12-20-2022, 05:54 PM
            • wolf1976
              wireless receiver for 6 speeds fan control with remote control
              by wolf1976
              hi i have a receiver that is destroyed from the overvoltage i guess
              my question is has three wires u v w for driving a motor fan i found an other receiver wireless from aliexpresss with the same propertiew but for dc motor
              the motor fan has not label
              i have an other receiver operational
              In your opinion can i measure the voltage at the output ?
              what do you suggest me with a simple instrument multimeter or using someone instrument more specific ?
              thanks in advance...
              07-23-2025, 03:12 PM
            • budwich
              onkyo 919 Receiver... hum problem but...
              by budwich
              I have an onyko 919. It has a hum problem at cold start which eventually dies / goes quiet. I have been "chasing" it for a while. Tightening ground screws and checking a few places. Basically, the problem is in the "back half" of the unit.... that is, if I take the sound out of the "pre-out" and feed it to a stand alone amp, it is good. If I feed in a signal at the external decoder input and play thru the back end of the onkyo, it has the hum.

              Anyway, along the way (the chase), a number of components (resistors, capacitors, etc) on the main board...
              01-13-2021, 03:31 PM
            • CdDvdFlash
              DSE GE6878 possible TV receiver dying remote not working well
              by CdDvdFlash
              For this Dick Smith TV GE6878 (Thompson) I replaced the broken remote with a universal it kinda works though if its more than a few meters away sometimes the buttons register and sometimes they wont so I bought another remote from another brand and it has the same problem, I've had an old TV in the past that the sensor died completely and I replaced it to fix it could this be a similar problem? I tried looking for a service manual, spare parts for a receiver and a parts list but I couldnt find any info. can someone please help me to find the info online for a service manual or where I can buy...
              07-03-2024, 03:55 AM
            • JordanW
              Diagnosing NAD receiver -- unexplained shut-downs
              by JordanW
              Everyone -- I am trying to troubleshoot my NAD C740 stereo receiver, which either won't power on or won't consistently stay powered on.

              I will start by saying that I am a hobbyist, and while I am decently handy with basic DC stuff, I am more hesitant when it comes to mains-powered equipment (that is, reluctant to poke around with a multimeter when it is powered on)

              The central issue is that after a long period of non-use, the receiver powers on and all functions seem to behave normally, but after a couple of minutes, it powers itself off.

              If I attempt...
              01-02-2023, 11:43 AM
            • Loading...
            • No more items.
            Working...