Pico osciloscope adc200/50

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • cloepula
    Member
    • Sep 2009
    • 49
    #1

    Pico osciloscope adc200/50

    Hi to all,
    Today i just bought my first scope.
    Is a digital pc scope, Pico adc200/50. Have 20v max voltage and 25mhz 2 channel. Have one probe 10x, this will be for 200v, but will buy a 100x probe for
    2000v. Will this scope be anough to investigate on smps power supply and somme other electronics like lcd monitors, computers mainboard, and maybe laptop.
    Any help is greatly appricieted and thanks in advance.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • howardc64
      Don't probe Samsung LED conector with LED tester, connect may not make contact afterwards
      by howardc64
      Samsung have been using this style LED connector for few years now



      Usually good idea to test the LEDs before opening the panel to change them. I do this without the PSU stil connected. With this connector (white one) have to jam the LED tester probes in the very narrow thin slot where the PSU blade style male prong inserts into. I've done this on many Samsungs without problem until today...

      The female terminal inside the white connector has fragile fingers that grabs onto the male blades on the PSU's black connector. If the LED tester probe spreads open...
      10-12-2025, 08:13 PM
    • perfm2
      Wson8 spring pin probe WORKS
      by perfm2
      I couldn't find anywhere on the internet where someone had discussed actually using one of these newer wson8 probes for flashing your Wson8 BIOS chip without removing it from the MB.
      I recently ordered one to give it a shot and it actually worked quite well.

      The tricky part is obviously keeping the probe pins in place on the exposed Wson8 pads of the MB while reading/writing.
      I used a larger binder clip attached to the top of the probe to create a large flat surface, then added about 1lb of weight to it.
      This aided greatly in allowing the probe to stay in place...
      03-30-2023, 11:19 AM
    • repair-it
      Need advice testing a samsung power supply board with scope
      by repair-it
      I am attempting to test a samsung power supply board to verify the pfc ic is working. I am powering up the board with my isolation transformer. The board turns on fine but when I attempt to connect the ground for the scope probe, it trips out the isolator. I was taught not to 'float my scope' so I am wondering if I should test without connecting the ground lead or would that be asking for trouble? Not sure how else to test, I don't have a portable scope. I could plug direct to mains power but that would bypass the safety factor.
      07-12-2025, 11:00 AM
    • Jane
      How do you test MOSFET in laptops ?
      by Jane
      I tried to use this method:

      Testing an N-channel MOSFET:

      Step 1: Discharge the Gate (turn off the MOSFET)
      Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
      Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

      Step 2: Charge the Gate (turn on the MOSFET)
      Now, place the red probe on the Gate (G) and the black probe on the      ...
      09-27-2024, 03:31 AM
    • sam_sam_sam
      Hantek scope that can hook up to your iPad or computer IDSO1070A feedback wanted about it specifications
      by sam_sam_sam
      I thinking about about buying one later on this year depending on what feedback I get from this forum members that know more than I do about what is importance about what to have in a scope

      https://www.aliexpress.us/item/32568...3333736563%21s...
      04-12-2025, 10:24 PM
    • Loading...
    • No more items.
    Working...