The best Brushless Impact Driver

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • capwizard
    Badcaps Legend
    • Jun 2016
    • 1991
    • USA

    #1

    The best Brushless Impact Driver

    Hitachi WH18DBDL2 18-Volt Cordless Lithium-Ion Brushless Triple Hammer Impact Driver Kit $399.00..............The Best.......

    Hitachi Triple Hammer 18v Brushless Impact Driver WH18DBDL2
    https://www.youtube.com/watch?v=drsHsFuU3Vk

Related Topics

Collapse

  • osrex
    LED DRIVER KEEPS DYING
    by osrex
    Hello, this is my first post and im just a beginner, so be easy on me guy. thanks



    i have a LED chandeilier that switches colors from white to cool white to warm when toggling the switch, it has 24 LED arms, each arm is 30 CM length.



    i have no datasheet at all for the LED lights, all i have is its length.



    long story short, testing the chandelier on the ground, and it works fine for 1 - 2 - 6 hours, no problem.



    as soon as i fix the chandelier to the ceiling and bury the driver inside the hub,...
    05-05-2025, 03:36 PM
  • ut-norm
    Driver brushless motor
    by ut-norm
    Hi everyone, I have a brushless motor, of which I am attaching a photo mounted on a DEWALT battery saw that has a faulty controller driver but with the windings ok. I would like to feed it with another controller driver (after having obviously removed the broken one mounted on the base of the motor ) but I don't have clear ideas about it. I've seen many controllers on Aliexpress but I don't know which one to get. It should have a locking system like the original one in case of engine jam.
    Can you help me?
    Hello everybody....
    04-06-2023, 09:09 AM
  • flat-earther
    help repair Scorpion SC-6989 12v cordless impact driver
    by flat-earther
    Hi I got this Scorpion High Quality Products model SC-6989 12v impact driver and the problem is it only runs on full speed and LED light doesn't light up.
    I got the tool with two dead batteries and I already using the good 18650 cells from the two made one working battery.
    Initially when I got it I once hooked up a good 12v battery to it and it powered up and LED worked but now depressing the trigger only makes it run on full speed or nothing so there's no variable speed, but to be honest I'm not sure if this tool has a variable speed trigger. Also LED doesn't light up anymore....
    03-06-2023, 06:57 AM
  • howardc64
    Vizio E55-F1 dark backlight zones. LED failure or Dimming Zone Driver?
    by howardc64
    Problem

    Fixing a dimming zone TV with LEDs not lighting up. Dimming zone circuit introduces added variable to diagnose LED and/or Dimming Zone Driver board? Some 1/2 rows of LEDs appears to be out in active dimming zone off AND some brightness flickering with active dimming zone high while playing changing video



    Model & Board Pics



    Conflicting Spec

    Vizio indicate this TV has 10 dimming zones. However, LED strips and Zoned light driver connector suggest 12

    https://www.shopjimmy.com/vizio-gj-2k1...
    10-10-2024, 01:16 PM
  • eccerr0r
    old X58 triple channel board... memtest86 memory speed?
    by eccerr0r
    Anyone run memory speed tests with an old X58-based triple channel 1st gen or any other >2 channel board? The one I have is a Gigabyte I think.

    Anyway I had four 4GB DDR3-1333 modules in the 6 memory slots and got around 11GB/sec memory speeds assuming that it went dual channel since it didn't have enough modules for triple channel. Now I stuck in two more 4GB modules, but they are DDR3-1600. I'm still getting 11GB/sec speeds according to memtest86...

    Just wondering, anyone do memory speed analysis on these triple (and higher) channel memory boards? Are there any...
    06-28-2025, 09:06 AM
  • Loading...
  • No more items.
Working...