unknown resistance at mosfet

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • mrxenot96
    New Member
    • Oct 2014
    • 2
    • Hungary
    #1

    unknown resistance at mosfet

    Hello everyone, I'm new to the forum and would like to get a few answers from the members. Firstly, sorry for my bad english, I try to correctly write.
    So, I have a Zotac 9800GT, what had shorted MOSFETs. It worked well 2 month ago. I replaced them but unfortunately a component ( I think a resistor which set the operating point) had broke down. I don't know what component is it I replaced that with a variable resistor (because the 2 pads directly connected to the 6-pin's +12V and ground) and I increased the resistance until I measure 1,37kohm on that (R=U/I) because it need on full load 105W, and the capacitors are tear on DC. But nothing happen. So here's my questions:
    1. Had I correctly calculated the input resistance, or is it a big mistake?
    2. Can someone measure me the input resistance of an other Zotac 9800gt?
    3. Is it possible that the GPU died?

    Thank you in advance for your answers.
    Last edited by mrxenot96; 10-04-2014, 11:06 AM.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Nooy
      VGA MOSfet permanently shorted and loss of MOSfet pad
      by Nooy
      Hello everyone, I recently found this badcaps site and super Learn Electronics Repair youtube channel. And I wanted to learn how to troubleshoot power supplies and VGA cards and how to practice soldering, since I already have a properly defective piece of them. I am currently trying to solve two problems:

      I have a Gigabyte GV-RX460WF2OC-4GD type card. I managed to find the faulty MOSfet (AON6414A) on it, which I replaced. The card starts up, but after about half a minute, the MOSfet in the same position will be shorted again. Is it possible that the PWM controller driving the MOSfet...
      02-14-2024, 02:26 AM
    • Jane
      How do you test MOSFET in laptops ?
      by Jane
      I tried to use this method:

      Testing an N-channel MOSFET:

      Step 1: Discharge the Gate (turn off the MOSFET)
      Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
      Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

      Step 2: Charge the Gate (turn on the MOSFET)
      Now, place the red probe on the Gate (G) and the black probe on the      ...
      09-27-2024, 03:31 AM
    • redbaron1007
      Help identifying mosfet on Razer Blade RZ09 (CH570_MB_NT)
      by redbaron1007
      I have a Razer laptop (RZ09 MB# CH570_MB_NT) that has a shorted mosfet marked BND M03 E067 that I'm unable to find anywhere online. Does anyone either know what the part number is for this mosfet or have a schematic I can find it in?

      Backstory on the whole thing the laptop was plugged into a lamp at a hotel. The lamp got unplugged while it was charging and now the system won't power on anymore. I found the caps around this mosfet shorted and when I injected voltage into the caps the mosfet got hot and my bench psu was pulling 5A. Pretty sure this is all that's wrong with the laptop...
      1 Photo
      09-09-2025, 11:10 AM
    • Nagy Daniel
      Lowest possible resistance on laptop motherboard rail - Guide Table request
      by Nagy Daniel
      Hi, I'm Daniel, and I'm new to the world of repairing motherboards.

      I would like to create a table, or more likely a guideline about the voltage rails and their possible resistance rail.

      I know that the motherboard design has a very big depend on the rail's resistance, but I would like to know what is the smallest value for a rail that can be acceptable. For example, I heard that some new gaming motherboards can have 0,5 Ohm resistance on the GPU rail, but on an older type, it could be a sign of a shorted GPU rail.

      So, I generated a table with AI so I can...
      03-04-2025, 08:24 AM
    • MicroSMD Lab
      ASUS ROG Zephyrus GPU Mosfet repeat failure
      by MicroSMD Lab
      The board number is GU502DU. I repaired this a couple weeks ago and it came back with the same issue, same mosfet failed (PQH9201). I'm hoping that the GPU was spared this time.
      I used the same replacement part (purchased from Mouser) and I'm certain the soldering was done properly since it took just as much effort to remove as before. What could cause this same mosfet to fail? I'm thinking if it was unsuitable then the others would fail too. I looked for similar failures on YTube and the mosfet was replaced with AOE6930 in one instance and AOE6932 in the other but it's possible that the...
      01-10-2024, 06:36 AM
    • Loading...
    • No more items.
    Working...