Component identification please

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Techie_hobby1
    Senior Member
    • Feb 2023
    • 56
    • England

    #1

    Component identification please

    Could anybody identify this component please. It is connected to a Lipo battery management board.
    i am just trying to troubleshoot this component
    many thanks
  • Techie_hobby1
    Senior Member
    • Feb 2023
    • 56
    • England

    #2
    Correction- I meant to say Li-ion battery not LiPo

    Comment

    • harp
      Badcaps Veteran
      • Jun 2022
      • 598
      • Planet Earth

      #3
      May be some type of sense resistor, but probably the self-desctructive fuse with heater.
      Attached Files

      Comment

      • Techie_hobby1
        Senior Member
        • Feb 2023
        • 56
        • England

        #4
        harp brilliant thank you.

        Comment

        Related Topics

        Collapse

        • DynaxSC
          Activation of Management Engine after exchange Z590 chipset - ASUS PRIME Z590M-PLUS
          by DynaxSC
          Hi, i have an ASUS PRIME Z590M-PLUS board, which had an shorted Z590 chipset. I have succesfully exchanged the chipset to a factory new one, however there is a serious problem with the Intel Management Engine (later on: ME) not beeing activated after the chipset device replacement.

          For lower chipset families (on ASUS boards) it worked to program the oldest bios version into the SPI rom, and the bios had activated the Management Engine itself by default - there was a message on the screen prior booting - "BIOS is updating Management Engine ..... . Do not shut down to prevent...
          06-10-2023, 11:30 AM
        • Rhork
          Identify Power Management chip DELL E7240 (LA-9431P)
          by Rhork
          Hello,
          I have a problem on a DELL E7240, LA-9431P motherboard (rev 1.0).
          This is a laptop that I recovered, it had liquid dammage and had corrupted bios.
          I reprogrammed bios + ec (v A.29 ME Clear)
          I cleaned everything, after reassembly, it boots and it smells like burnt after a few seconds ... I disassembly the motherboard and see that the Power Management chip (in attached photo) has burnt!
          It's the P800 chip on the schematic repair, and suddenly I can no longer read the info on the chip, if someone can direct me to avoid having to buy a used motherboard and...
          02-06-2021, 06:14 AM
        • Techie_hobby1
          Help please with identification of few components for troubleshooting (Solar Water Fountain circuit)
          by Techie_hobby1
          Need some help please with a few components on this small board so that I can troubleshoot the circuit.

          The PCB is a Single sided board fairly simple circuitry has a +ve and -ve Solar cell power input, a 7.4v 1500mAh (dual 18630 cell) power in which the Solar panel charges the cells, and lastly the Output goes to a DC connector...
          J1 is actually 1P1T Switch (in ON position completes Battery cell circuit
          J2 - to DC Output
          J3 is Battery cell connector

          however I am struggling to identify if:
          Y1 (SOT-23) are NPN Transistors, MOSFET's or 11v Zener's....
          Yesterday, 12:43 PM
        • thesame
          DVR HIKVISION DS-7208HWI-E1/A BOARD DS-80104 REV 2.2 help identify burnt components
          by thesame
          Hy guys , i have a DVR board DS-80104 REV 2.2 that was powered wrong, i have some smds on the board that are blown and i can't identify them , maybe if someone has this board somehow and we can identify the smds', i have searched online and i can't find a schematic.
          The smds are SOT-23-6 , one of them i think it has the marking ADJF since i found another one on the board with this marking , but the other one it seems that it starts with AG or it looks like. I would really apreciate if someone could help me identify those IC's .

          ​...
          02-27-2024, 04:31 AM
        • chth96
          How can I identify varistor which have been blew up?
          by chth96
          I mistakely pluged 100v japanese retro game console to 220v outlet.
          So It seems that glass fuse and varistor have been blew up.
          I can identify that voltage and ampere value of glass fuse(250V LF 1.6A),but It is impossible to identify varistor type in my sega saturn PSU(YAMAHA 35M07U XR258)
          Is there any way to identify varistor type in my sega saturn PSU?
          Any reply would be appreciated.


          EDIT:
          It seems that I finally found out what type this black varistor is. It is Panasonic ERZV05D221 “ZNR” Transient/Surge Absorbers (Type D) Varistor Voltage...
          11-26-2023, 08:52 AM
        • Loading...
        • No more items.
        Working...