Re: bad neutral on new house
That must've been an aw-fuck moment. Did you get a measurement?
I forgot the smiley
That must've been an aw-fuck moment. Did you get a measurement?
I forgot the smiley
-
Last edited by SteveNielsen; 04-09-2014, 09:04 AM. -
Things I've fixed: anything from semis to crappy Chinese $2 radios, and now an IoT Dildo....
"Dude, this is Wyoming, i hopped on and sent 'er. No fucking around." -- Me
Excuse me while i do something dangerous
You must have a sad, sad boring life if you hate on people harmlessly enjoying life with an animal costume.
Sometimes you need to break shit to fix it.... Thats why my lawnmower doesn't have a deadman switch or engine brake anymore
Follow the white rabbit.Comment
-
Re: bad neutral on new house
Considering it's a mains feed... Jesus, glad it didn't knock your dick in the dirt.Comment
-
Things I've fixed: anything from semis to crappy Chinese $2 radios, and now an IoT Dildo....
"Dude, this is Wyoming, i hopped on and sent 'er. No fucking around." -- Me
Excuse me while i do something dangerous
You must have a sad, sad boring life if you hate on people harmlessly enjoying life with an animal costume.
Sometimes you need to break shit to fix it.... Thats why my lawnmower doesn't have a deadman switch or engine brake anymore
Follow the white rabbit.Comment
-
Re: bad neutral on new house
So glad we take health and safety seriously Down Under (at 230V AC/415V at pole)...Comment
-
Re: bad neutral on new house
The circut breakers plug on the panel's buss . If they fall out when you take the cover off , there some major problems with the panel . If the o.p. of this thread knows how to use a volt meter then he/she could check the voltage between the ground and the neutral at the panel . If there is a voltage between the ground and neutral , then the problem is before it gets to that panel .Comment
-
Hi:
i am trying to repair this Christmas lights from my parents. They are incandescent lights, no led lights.
I have tried with 12V a 24V small lights that I found in Aliexpress but is obvious that are not the right ones. They last microseconds connected. Do they blow because of Amps or Volts?
If I measure the Amps in the string........it's only 90mA. If I measure the Volts in the "green box"......it's between 0 and 190V, but doing a little bit of maths from the number of bulbs in series.......it's only about 6V per lamp.
Could... -
Hello,
I have a Lenovo here that does not want to power on. The motherboard appears to be clean, no sign of corrosion or obvious fried components. When plugged in, I see 3 blinking lights and then off. It would cycle the 3 blinking lights every 10 seconds or so as long as I have the adapter plugged in. Amp meter shows 20 volts, 0.224 amps, no fan spin, red light indicator near the charge port.
Thermal camera shows a section of the motherboard that is warmer than the rest. It is near the connector labels JRTC1 (CMOS battery). Diode measurement to ground for pin 1 = OL,... -
Does not turn on, lights 3 of the 4 LEDs and turns off and stays like this, presses the power and repeats.
I saw that the room LED lights up only when the screen is connected, so quiet.
We have all the power supplies, even processor, 1.8V
One thing I found strange, it has a very low resistance in the Vcore is giving 1 Ohm , work with notes and such, I know that this is normal in some processors but with this resistance only take video card so found it strange.
I suspect that there may be some leak in the processor.
Anyway, when I press the power, it... -
My Mom bought some cheap motion sensor lights on wish... then complains about about batteries and this thing chews though them, well it uses 4 AAA batteries and a pack of rechargeable ones is about 13 USD
well since it uses 4 AAA and rechargeable are 1.2v and non-recharge at 1.5 this thing must work with 4.8-6v, I'll shove a USB cable on it, infant i will use a broken phone charge cable... dam this thing uses 430 mA and they made it battery powered...
lets ignore the fact that i thought the board fit both ways... and the wire color is reversed going to the board... -
Hia, I'm pretty sure am having an issue with an LED driver on my grow lights.
Video's...
https://drive.google.com/file/d/1Odp...ew?usp=sharing
https://drive.google.com/file/d/1OcV...ew?usp=sharing
Photo's of driver circit..
https://drive.google.com/file/d/1OjX...ew?usp=sharing
https://drive.google.com/file/d/1Oj5...ew?usp=sharing
One side of the lights were working correctly at 70v the other day and the other side was...
Comment