I'm new to I2C programming, and I need to find out / learn how to program R/W RTS5450 and RTS5441.
What hardware and software do I need?
What hardware and software do I need?
-
-
I am in the same situation. I need to program a RTS5450M for a BenQ SW271C-B monitor. Does anyone have any information on this? Thanks. -
i am facing same issue. Could somebody make a tutorialon it.
thank youComment
-
successor and ufpi programmer are able to do this. if you own one of these join their telegram group. the will help there.Last edited by rediii; 03-02-2025, 02:25 PM.Comment
-
I was finally able to easily read and write an RTS5450M!!!
I purchased an Alexsof RTS5450M configuration board and my SVOD4 programmer, but it's compatible with other programmers.
You can find that board here: https://alexsof.com/product/rts545x-...ller-firmware/
Be sure to check out the website because there are other resources, such as the MPS phase controller programmer or the DDR4 test, that are super interesting.Comment
-
xgecu programmers dont list it.
Comment
-
Comment
-
Comment
-
I'm attaching the file for the RTS5450M used in the Lenovo P24H-2L LCD monitors in case it's useful to any colleagues. https://www.badcaps.net/forum/troubl...-rts5450m-dump
As I recover dumps, I'll upload them. I'm still planning to extract the one from a 1,600€ BenQ monitor...Comment
-
Model : X390 yoga 8th
Board name : lbb 1 mb 18729 1
Issue : I can read the file but when programming it does not complete the programming
I have a successor base 2 programmer but I can't program the NPCE388PB0BX chip...09-22-2024, 08:33 PM -
Epson M3170 Monochrome inkjet printer adjustment program tool.
Hi, i want to reset a epson reset program tool needed to reset the EPSON M3170 PRINTER's Maintenance box,
anyone having it, please share
Thank you -
My wife is asking me about getting one because our electric bill was that it has ever been even more than last year at this time nothing has really changed since last year last month unless the electric company has done some fuel adjustment charges I have not done any investigation into yet but I might have to but there was a time back a few years ago that I use to set the temperature warm during the day when we were not home but when we got wooden floors in our house and you have to keep the humidity down to keep it from warping I just set to a temperature to 75*F to keep the humidity down but...
-
Recently I've gotten into EC flashing due to my broken laptop(s) and started frantically searching methods for flashing the IT5571E-128 chip on the cheap(due to me beaing a student and not having a job) and noticed that ITE newer chips can be flashed via ISP (In-System Programming) either via SMBus or the KBC (EPP - Enhanced Parallel Port) interface. While these can be achieved with programmers like SVOD4/3 or the RT809H/F those options are WAYYY out of my budget so I was horrified. But recently I stumbled uppon some programmers on aliexpress that claim they can program a variety of ITE chips...06-17-2025, 07:17 AM
-
Greetings and salutations!
I have a device that uses an N32G455RE. Unfortunately, its flash got corrupted. I have a dump of a working chip.
How can I program a specific region of the flash or the whole flash without touching the RAM, option registers, etc.?
I do not have a J-Link debugger and won't buy one, as I am not rich.
I have flashed a Nucleo board with an ST-Link to a J-Link just to find out that the ST-J-Link only supports ST chips.
What would be the cheapest and easiest option to program the Nations chip's flash without touching registers etc.?...
Comment