Reading Resistance with Multimeter

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • General_T
    Member
    • Sep 2013
    • 36
    • Canada

    #1

    Reading Resistance with Multimeter

    Hi,

    I am new to this and am trying some very basic projects to get some sort of understanding with electronics.

    I put a 1k ohm resistor on to a breadboard to see what the resistance would be. I assumed it would be the same as when it is just by itself.

    Tested by itself (not on the breadboard) my multimeter (fluke 179) reads 1k ohms - as I would expect. But when I place the resistor on the breadboard - all by itself with no power - the multimeter reads .2 ohms. Why does it not read 1k ohms?

    Appreciate any insight to this as I expected it to read near 1k ohm.


    Thanks
  • mariushm
    Badcaps Legend
    • May 2011
    • 3799

    #2
    Re: Reading Resistance with Multimeter

    HOW did you put it on a breadboard?

    A breadboard has all the holes in a vertical line connected together. So, if you put a resistor that way, the resistor is shorted and you're basically measuring the resistance of the probes' wires.

    Attached Files

    Comment

    • domas
      News Hater
      • May 2013
      • 323
      • Denmark

      #3
      Re: Reading Resistance with Multimeter

      put it into the breadboard in another direction, i think you "shorted" the resistor

      Comment

      • General_T
        Member
        • Sep 2013
        • 36
        • Canada

        #4
        Re: Reading Resistance with Multimeter

        D'oh - if it can be done - wrong - I will do it!!

        Thanks Guys.

        (SIGH - so much to learn!!)

        Comment

        Related Topics

        Collapse

        • MidnightRoller
          Can a resistor lose resistance after hot air?
          by MidnightRoller
          I am curious if a 0402 resistor could go from 43 ohm to 0. In electronics class and my experience a resistor can degrade and gain resistance all the way up to not being able to conduct at all. I have never heard of a resistor decreasing in resistance and becoming 0 ohm or a dead short… that's not the direction they fail… or so I thought.

          I was attempting to remove a wson8 chip on an iMac motherboard and it required a lot of heat, on one side of the chip were 3 0402 resistors that were very close. I popped the chip out unintentionally out of the tweezers and sent those resistors...
          02-02-2022, 11:46 PM
        • flat-earther
          Hoover FM216LI cordless vacuum refuses to charge
          by flat-earther
          I have a Hoover FM216LI cordless vacuum which isn't charging its internal battery.

          I opened up the unit, and it has 6x Samsung ICR18650-22P cells connected in series.
          5 cells were at about 3.3-3.1V. one was at 2.4V, so I assumed this cell was bad that's why the vacuum wasn't charging so I replaced it with another 18650, but after that the problem still persists, the vacuum turns on a bit and then cuts out since the batteries are empty.

          So I think the over discharged battery wasn't the culprit, it was a symptom of the unit not being able to charge its batteries....
          06-06-2025, 03:14 AM
        • harp
          high voltage high resistance marking resistor
          by harp
          Is there any reason why high voltage high resistance resistor use weird marking and value on it? Standard nomenclature, EIA value not used?...
          08-26-2024, 01:42 PM
        • jinu_j
          Dell 2209WA - power supply - Fusible Resistor replacement
          by jinu_j
          Hi

          I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

          1. FR950 - blown fusible resistor - 0.2 Ohm 1W
          2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
          3. R835 - Blown Resistor - 20KOhm SMD resistor
          4. D930 - Shorted Schottkey Diode...
          05-03-2025, 10:51 PM
        • mikey5791
          Need help to replace burned resistor in 350w atx psu
          by mikey5791
          Hi to all forum members,

          Got this faulty 350 watt atx psu dirt cheap from a local online seller as i am keen to use it as a learning tool to repair faulty power supply.
          The faulty part is quite obvious from the burn area near the 16pin KA7500 BD pwm. The fuse is still intact with good continuity.

          Upon power on ac, there is 5vdc standby power on cathode of diode D14 and about 10vdc on cathode of diode D13.(This should be the aux power to generate the 12v and 5v rail.)
          Initially i replace the two burned resistors near my marked red arrow to 200 ohm resistor...
          12-26-2024, 04:55 AM
        • Loading...
        • No more items.
        Working...