Need Chang capacitors datasheet

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Koda
    Badcaps Veteran
    • Aug 2011
    • 317
    • Macedonia

    #1

    Need Chang capacitors datasheet

    Hi guys I need to replace some Chang capacitors and I can't find the manufacturer website or the datasheet for these caps. They are all 1000uf 25v caps and no other markings on them except for the rated temp which is -40+105*C. Can someone help pls.
    Guns don't solve problems. I'll take 12
  • mockingbird
    Badcaps Legend
    • Dec 2008
    • 5484
    • -

    #2
    Re: Need Chang capacitors datasheet

    Here is their datasheet page:
    http://www.huaweiec.cn/product04_e.asp

    Comment

    • Koda
      Badcaps Veteran
      • Aug 2011
      • 317
      • Macedonia

      #3
      Re: Need Chang capacitors datasheet

      Originally posted by mockingbird
      Here is their datasheet page:
      http://www.huaweiec.cn/product04_e.asp
      Thanks you
      Guns don't solve problems. I'll take 12

      Comment

      Related Topics

      Collapse

      • Olkus
        Thomson capacitors - looking for datasheet
        by Olkus
        Hi,

        I can't find anything about this caps - maybe someone have a datasheet?
        And are they good quality?
        09-15-2023, 03:14 PM
      • dragon3x
        After updating motherboard capacitors, what to do next (Asrock K7VT2, SOLTEK SL-75FRN2L)
        by dragon3x
        Hi, I have some 32 bits computer motherboards that need repair, as they fail to
        power on.

        Here are some examples :

        (N.B. "capacitors" indicated here are electrolytic capacitors located in the onboard
        switching supply area).
        (N.B. #2 : I could not find a 3300 microF aluminum-polymer with a higher voltage
        than 6.3 V.)

        1 - Motherboard #1 : this is an Asrock K7VT2 (socket A) that still works well. To put it on test
        I replaced capacitors with aluminum-polymer.
        3300 microF/6.3 V. x 4 replaced by 3300 microF/6.3 V. (KYOCERA...
        03-21-2025, 02:46 PM
      • slybunda
        AA and AAA battery charger capacitors?
        by slybunda
        hey all, iv got my favourite battery charger here which iv had for many years probably 15 years now or maybe even more. it still works good but thought id open it up to clean the dust out of it, lots of dust inside but now its clean and noticed 4 capacitors inside it and wondered if i should replace them.
        it has inside:
        2 x 47uf 16v caps 105c branded as Su'scon (lol sounds sus to me)
        2 x 470uf 16v LZ105c branded as G.Luxon

        not heard of these brands are they any good?

        iv attached photos of the charger and the board inside for an idea on the type of...
        12-24-2023, 04:41 AM
      • sam_sam_sam
        Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
        by sam_sam_sam
        I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

        This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

        After all of...
        07-13-2024, 08:14 PM
      • Ady2017
        Are there any datasheets available for Elna RJG capacitors?
        by Ady2017
        I have a 2007-era Panasonic VHS combo that is full of of Elna RJG capacitors. I am trying to test the capacitors to diagnose the machine and then select replacement capacitors but I can not find any datasheets for them. I did find a Elna catalogue from 2007-2008 but there is no mention of this capacitor series. Where these specially made for Panasonic and so not made available to the public? Any ideas what to find out what the ESR values should be without the datasheets? They are all between 10V and 50V and 47uF and 1800uF. None are leaking or bulged but I know that they need to be tested to be...
        05-25-2025, 02:19 PM
      • Loading...
      • No more items.
      Working...