Removing SM chips

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • barry wilkins
    Senior Member
    • Aug 2009
    • 172

    #1

    Removing SM chips

    Hi does anybody have experience with removing surface mouted IC s and the like. I have managed to do this in the past with small deivices ,but it is difficult to do without damaging the chip or the pc print .
    I understand there is a solder available which stays molten long enough for you to remove the device easily .
    Any body know any thing about this ?

    Barry Wilkins
  • jetadm123
    Badcaps Legend
    • Feb 2010
    • 2169

    #2
    Re: Removing SM chips

    It's called ChipQuik. There are several demo videos on YouTube.

    Comment

    • yyonline
      Badcaps Veteran
      • Jul 2009
      • 692
      • USA

      #3
      Re: Removing SM chips

      You can order a sample from the chip quik website:

      http://www.chipquikinc.com/

      And it really does work like they show it in the videos. I don't do surface mount stuff that often, but it's certainly useful when I do.

      Comment

      • TheLaw
        Badcaps Veteran
        • Jan 2011
        • 477

        #4
        Re: Removing SM chips

        Solder wick? Stuff works quite well for surface mount, but you might fry the chip...

        Yes chip quik is a good solution.

        Comment

        • severach
          Badcaps Legend
          • Aug 2007
          • 1055
          • USA

          #5
          Re: Removing SM chips

          A SMD hot air gun is a lot cleaner than chip quick and solder wick and the chip is usually fine. With a little experience swapping SOIC-8 chips is easier than it swapping DIP-8 chips. Hot air has a lot of other uses too.
          sig files are for morons

          Comment

          • digge
            Badcaps Veteran
            • Apr 2006
            • 296

            #6
            Re: Removing SM chips

            I use a hot air gun as well sometimes, just need to be careful not to heat too much, since its not as precise as any professional equipment for the job. In some situations you might not want to use one since you might desolder whats on the other side of the board or close to where you are working. Some tinfoil or sheet metal with a hole in it could help lead the heat away from what you're trying not to desolder.

            Comment

            • Uranium-235
              Comrade Glimmer
              • Aug 2007
              • 5042
              • US

              #7
              Re: Removing SM chips

              Originally posted by severach
              Hot air has a lot of other uses too.
              true, like reballing

              oh and washington, lots of hot air there too! <rimshot>
              Cap Datasheet Depot: http://www.paullinebarger.net/DS/
              ^If you have datasheets not listed PM me

              Comment

              • Scenic
                o.O
                • Sep 2007
                • 2640
                • Germany

                #8
                Re: Removing SM chips

                Originally posted by Uranium-235
                oh and washington, lots of hot air there too! <rimshot>

                Comment

                Related Topics

                Collapse

                • ugamazing
                  Best place to source RAM chips? 8GB 820-00850 boards to 16GB or 32GB
                  by ugamazing
                  I'm looking to upgrade several 8GB 820-00850 boards to 16GB or 32GB for personal use. I am curious what the best practice and process is for sourcing new replacement chips, and what vendor(s) you guys prefer? Another question is, how do I find compatible chips and their corresponding part/model numbers? For example, in the 820-00850 schematic, the DDR chip U2600 model listed (EDFB232A1MA) corresponds to 1x32GB chip. Of course, I would need 4x8GB chips to replace the 4x2GB chips currently on the board. How do I find compatible 8GB chips? Is it as simple as searching "BGA178 8GB 2133"...
                  08-31-2022, 07:34 AM
                • acedogblast
                  Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
                  by acedogblast
                  This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

                  There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
                  11-02-2024, 05:13 PM
                • feherhollo
                  WSON8 NEW Bios Chips READ, ERROR, ETC.
                  by feherhollo
                  Hi,
                  I asking for help on some new WSON8 256MB chips. Please share your experience. I faced error on some new chips on read, erase, write with different programmers. These new chips are not exist in any programmers database. (GD25B256D, XM25RH256, W25Q256JV so on.)
                  I'm using RT809F V.5.0, EZP2023 Pro, CH341A Green

                  For the exact experience with GD25B256DYIG is RT809F erase the chip under 33sec. This kind of 256MB chip normal erase time is 70-120sec so I think not all the partitions are erased. If I do blank check or reread the buffer says FFFFFF but when I write the correct...
                  11-26-2023, 09:33 AM
                • jimbofz
                  removing glued s/mount chips lg lb series
                  by jimbofz
                  recently struggled to remove BL0202 backlight chip
                  which had red residue of glue underneath
                  as well as annoying laquer over the top and surrounding area.
                  i had to use more heat than i like to remove it
                  which can cause bubbling of the bcb
                  i used two different types of flux,but it was the glue causing the problem .
                  just wondered if anyone has had this problem ,and if there is any solvent that may loosen the glue before desoldering?
                  (some vestel fets are also glued the same way)
                  this was on a LG47 LB585V,
                  I had replaced the led...
                  11-29-2021, 08:09 AM
                • Prott
                  [RoG Ally] Fault in one of the onboard RAM chips. Any way to diagnose which?
                  by Prott
                  Hello dear badcappers!

                  The title pretty much says it all - do you, please, know if there's any way to troubleshoot which of the integrated RAM chips (LPDDR5X in this case) is faulty?

                  Backstory:
                  After replacing the 4 onboard (soldered) memory chips on a RoG Ally (4x4 GB to 4x8 GB) it got stuck on the RoG logo. I assume one of the chips is either not soldered properly or faulty. However after reflowing and replacing bunch of them I am still stuck at the same place.

                  If there is a way to narrow down which memory module is faulty it would make my life much...
                  06-03-2024, 12:05 PM
                • Loading...
                • No more items.
                Working...