Cool weller Blog site for reviews

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • teeDee
    New Member
    • Jul 2006
    • 5
    #1

    Cool weller Blog site for reviews

    I have been wondering where I can go to get reviews on weller solder products, and I finally found a place, and it's right from the horses mouth.
    It's at All-Spec's blog site, actually you can get it from there, check it out.
    Weller solder reviews
    Tags: None
    • starfury1
      Badcaps Legend
      • May 2006
      • 1256
      #2
      Re: Cool weller Blog site for reviews

      Thanks teeDee will have a look later.

      Seems like getting decent reviews on test equipment is like pulling hens teeth

      maybe I'm looking in the wrong places but I find it very had to find them.

      cheers all
      You step into the Road, and if you don't keep your feet, there is no knowing where you may be swept off to." Bilbo Baggins ...

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Toueno
          Dyson Pure Hot+Cool HP00 - Datasheet needed
          by Toueno
          Hello,

          My Dyson Pure Hot+Cool, model HP00, no longer starts.

          After disassembling and accessing the electronic motherboard, I found that the 16A fuse soldered to the motherboard is dead. I decided to do an electronic shunt to see the reaction, and the Dyson turns on for a few seconds and then turns off.

          It is likely that a voltage control chip or a safety chip is dead, but without the electrical schematics, the repair becomes complicated…

          Thank you in advance for your help.

          Best regards
          ​
          08-14-2024, 10:38 AM
        • edugimeno
          Wine cooler flickers at startup and doesn't cool enough
          by edugimeno
          Hi there!
          I have an old wine bottle cooler, it's a basic peltier cell system with a power supply built in with the controller board, with a simple display at the front door and 2 push buttons to select the desired temperatura.
          Symptoms are it doesn't barely cool down, and makes a chirping noise at the board.
          Both fans on each side of the peltier are (now, after much cleaning) running smooth and silent
          When you turn it on, the front 7-segment display flickers for a variable time, usually like 1 minute but sometimes nothing or 3 minutes... Then turn on solid (but still some...
          03-01-2025, 04:51 AM
        • clearchris
          Old Weller 100/140 Watt Soldering Gun
          by clearchris
          Someone gave me two of these 100/140w weller soldering guns. Yes, I know it runs current right through the tip, but might be nice to really get some heat into some big wires that need to be soldered.

          So, worth a place on the bench, or chuck it?

          ...
          10-04-2023, 01:27 PM
        • Exman
          Weller WD1 with T12 Tips
          by Exman
          Dear BC,


          Today, by luck & chance I found a used Weller WD1 soldering station in my used local market for a very good price and I couldn't say no

          The seller sold it as it's with no warranty and no return, I accepted his t&c since he gave it on my asking price, only the station nothing else with

          My question, is there a way to mod a T12 with this station or someone did like this modification before


          Thank & waiting your replies
          04-10-2023, 02:39 PM
        • honigmann
          Dell 5591 overheating in memtest86+ but cool running Linux Mint - What causes this?
          by honigmann
          This machine comes with the i7-8850H, no internal drive and no battery installed, the bottom cover removed, an original Dell power supply is used. I just installed 8GB RAM, ran memtest86+ and noticed a power draw of about 40-50W. Accordingly within minutes the temperature went up to just below 100 degrees with the fan spinning wildly. Same thing when I enter the BIOS (1.20.0), around 40W power draw.

          Next thing I tried was an install stick with Linux Mint on it. Initially I am also at around 40W but with idle desktop (Xfce) it draws just 6,5W. Is this a BIOS issue? Version 1.34 is...
          09-23-2024, 08:51 AM
        • Loading...
        • No more items.
        Working...