2.5mm jack to 3.5mm converter

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • wan901
    Senior Member
    • Jun 2007
    • 69
    #1

    2.5mm jack to 3.5mm converter

    Hello guys...

    I have a converter from 2.5mm (4 ring) to 3.5mm (3 ring) converter for my phone. Well the things was working well , but is it possible to made this converter from the mono into the stereo ? im using N-Gage QD ^_^ .. if anyone have an idea please tell me ^_^ becuz i read at some forum that i search at Google last night someone told there is a converter that can make it ....sorry about bad english :P
    Tags: None
    • willawake
      Super Modulator
      • Nov 2003
      • 8457
      • Greece
      #2
      Re: 2.5mm jack to 3.5mm converter

      do you mean 3 ring or 3 pole
      3 pole = 2 rings and the metal = stereo
      4 pole = 3 rings and the metal = stereo + mic/button

      it is not possible to make mono into stereo of course, it becomes dual instead.

      i think the n-gage qd have 2 socket?
      which socket you want to use?
      what you want to connect to it?
      capacitor lab yachtmati techmati

        Comment

        Previous template Next

        Related Topics

        Collapse
        • CapLeaker
          VOIP, ATA REN and old analog phones ring voltage booster
          by CapLeaker
          I am working on a backup phone to VHF paging solution. Basically I am dealing with the old Zetron pagers. Here is how it works: One calls a number, the Zetron picks up, operator punches in the DTMF access code, the Zetron keys the transmitter and you can talk. press # the Zetron unkeys the transmitter and hangs up / times out.
          Now this setup works good on the old land lines, but not at all using a VOIP ATA. You can call all you want and swear like a bastard at the Zetron, but it will not (even if I threaten it's life) pick up.
          Yep, I know about the high ring voltage...
          12-10-2022, 09:27 PM
        • Document Archive
          MPS NB670 NB670GQ Switch Mode Converter for Laptop Computers Datasheet
          by Document Archive
          The NB670 NB670GQ is a fully integrated high frequency synchronous rectified step-down switch mode converter with 3.3V fixed output voltage. It offers very compact solution to achieve 6A continuous output current and 9A peak output current over a wide input supply range with excellent load and line regulation. The NB670 operates at high efficiency over a wide output current load range. Constant-On-Time (COT) control mode provides fast transient response and eases loop stabilization.

          Under voltage lockout is internally set as 4.65V. An open drain power good signal indicates the output...
          10-23-2024, 03:23 AM
        • gizmo1990
          What is this PSW1 part on a circuit board? Trying to fix a Canopus ADVC-300 DV/VHS Converter
          by gizmo1990
          I'm trying to fix this Canopus converter so that I can convert lots of old VHS cassettes. The problem is that it turns on for a split (and I mean split!) second, the fan jerks and then.. nothing. I've checked the power brick works. I've opened up the converter itself and been testing for shorts.



          The image attached shows the on/off switch (which I've checked works) to the left of the yellow socket. Below the yellow socket is a green block marked 26 with a strange symbol at the front. Putting my probes either end of this block, on the silver parts, gives an open short...
          10-21-2024, 08:02 AM
        • wolf1976
          i look for equivalent dc to dc converter
          by wolf1976
          hi
          in an inverter of aircondition i have dc to dc converter mes1515mh
          i have attachment the pdf file
          can i take a dual converter with two dc outputs instead this ? because i cannot found the same or is not possible ?
          the problem is instead 15 volt dc output i have only 6,45 volt
          thanks on advancxe...
          08-01-2024, 04:52 PM
        • md500
          [Question] Ch341a and 5v to 3.3v with logic converter
          by md500
          zz0.8tpitu4y0i8zzI bought a ch341a (I'm waiting for it to arrive) and I noticed that the programmer has a bug that the data pins go to 5v when the VCC pin is at 3.3v (which is the voltage I'm looking for).

          Instead of doing the 3.3v mod, I'm thinking of converting the 5v to 3.3v with an 8 channel TXS0108E through the ZIF socket but I don't know if that would work, because it has to circulate voltage and also information.

          What I am looking for is something that will convert from 5v to 3.3v but without modifying the ch341a.

          I can't buy the ch341a 1.6v that has...
          05-24-2024, 06:51 PM
        • Loading...
        • No more items.
        Working...