Capacitor compatibility - noob

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • CivicSpoon
    New Member
    • Dec 2013
    • 3
    • USA

    #1

    Capacitor compatibility - noob

    I recently had my LG L204WT monitor fail on my, and it's clear that at the very least some of the capacitors are bad (bulging/bloated). So now I need to find some replacement ones, which is where I'm having problems.


    This is what it listed on the side of the capacitors {they are all Samxon GF(M) 105°C8}:
    V7A 1000uF 16v
    V8A 1000uF 16v
    V5A 1000uF 25v
    V8A 680uF 25v (Two of these)

    I've tried searching for these, but haven't come up with any specific details, as to what it directly compatible. I have seen quite a few full kits, specifically for this monitor, but they list the V7A and V8A, as the same. I say they list them as the same, only because they specify a difference between the 25v and 16v ones, where it includes two 16v ones. Seeing as the part number is clearly different, I'm assuming they should in fact not be the same if I purchased new.

    Via a Sticky on here, I found the technical info on the Samxon GF series of capacitors (Here), but it's way over my head. I suppose what I'm really wondering is if anyone has any specific experience with this brand and series or capacitors, and could point me in the right direction, to find replacements. Even a company name and series, would be very helpful.
  • selldoor
    Slow Learner
    • Dec 2010
    • 7870

    #2
    Re: Capacitor compatibility - noob

    Try digikey look for panasonic FR FM FC series (best to worse )

    Or try badcaps.net
    https://www.badcaps.net/pages.php?vid=26

    You will need to be careful on the physical size
    Please upload pictures using attachment function when ask for help on the repair
    http://www.badcaps.net/forum/showthread.php?t=39740

    Comment

    • CivicSpoon
      New Member
      • Dec 2013
      • 3
      • USA

      #3
      Re: Capacitor compatibility - noob

      Ok, so I just have to match up the uF, volts, size, and shape? Then just pick the brand and series, and that's it?

      Thank you very much for the response.

      Comment

      • selldoor
        Slow Learner
        • Dec 2010
        • 7870

        #4
        Re: Capacitor compatibility - noob

        Almost - you must get low esr caps from a reliable seller. Panasonic FR FM FC from digikey.

        Badcaps.net only sells low esr caps. so guess its safe to say any he has with the
        correct voltage uf and size will be good.

        You can also go smaller in size with the same V and uf (Some newer caps are smaller)
        Please upload pictures using attachment function when ask for help on the repair
        http://www.badcaps.net/forum/showthread.php?t=39740

        Comment

        Related Topics

        Collapse

        • Prolog
          RTX 3080 FE Identifying capacitor
          by Prolog
          Hi people, I hope this is the correct spot to post this, I'm new to the forum.

          I have an RTX 3080 Founders Edition which has a burnt up capacitor (it was in parallel with another capacitor which appears damaged too), so I am hoping to be able to identify the capacitor values and order replacements.

          I hope these photos make it clear which component I am referring to:
          (yes, the soldering is a bit botched from removing the blown one, I know)

          I have found the board schematic (attached), but there does not seem to be a boardview available. I have never...
          12-01-2024, 08:27 PM
        • chth96
          If I replace with inferior capacitor, Is it No harm to other IC components at all?
          by chth96
          I replaced some capacitor which is located on optical pickup pcb which is shown in the table below(PCB #2).Because it have been out of order.
          Now,It works very well,But I just have found that all caps (6svpc100my and other part number as well) ,which is shown in the table below, has ultra-high ripple current spec.
          It is not able to obtain any capacitor which can be a substitute for this ultra-high ripple current nichicon capacitor.
          So I replaced it with samxon and rubycon's general capacitor(GP,YXA series).
          I know that these capacitor will not last as long as nichicon capacitor...
          12-22-2023, 04:34 AM
        • chth96
          How can I test non-polarized capacitor?
          by chth96
          I desoldered samwha NF capacitor(50v 5.6uf) from PCB circuit of 29inch CRT TV which have symptoms of no display after I heard sound of inrush of current to TV whenever I switch on this television.
          I measured ESR value of this non-polarized capacitor(samwha NF capacitor 50v 5.6uf) by means of MESR-100 ESR meter and It displayed 0.3 ohm

          And When I measured its capacitance with digital multimeter and LCR-T4 Mega328 meter, It displayed 10uf from DMM and 8uf from LCR-T4 meter.
          I found catalogue of samwha capacitor(samwha-catalogue_3.pdf file), which is attached to this thread,...
          06-02-2024, 07:31 PM
        • chth96
          Is it no harm to replace with capacitor without ripple current rating?
          by chth96
          When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


          Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
          But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
          Rubycon YK DataSheet (b...
          04-19-2024, 05:19 AM
        • chth96
          Should I replace polymer capacitor?
          by chth96
          a few days ago I finally purchased mser-100 v2 and I tested its abillity of measuring ESR value.
          I found that It shows pretty accurate ESR value for electrolytic capacitor,But When I measure polymer capacitor of dreamcast game console,I found that one third of polymer capacitor's ESR value is more than twice the value of ESR meter table.(for example, I measured one polymer capacitor of 6.3v 100uf, It showed ESR value of 7.68)
          Although my dreamcast now turns 20 years old but it still works. I occasionally have played game with it.
          Is this ESR value of polymer capacitor correct?...
          11-18-2022, 04:22 AM
        • Loading...
        • No more items.
        Working...