Panasonic VCC-Panel missing

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • MUNASHE
    New Member
    • Aug 2022
    • 5
    • South Africa

    #1

    Panasonic VCC-Panel missing

    Hie everyone
    I have a Panasonic TH-32A315M with standby light present. PCB number Tp.ms18vg.pb77. VCC-Panel missing.
    Please help

Related Topics

Collapse

  • BobbyMJ
    Panasonic TC-P60S30 - no standby voltage
    by BobbyMJ
    Hi All,
    Wanting to learn some electronics repair skills.
    I found a non working Panasonic TC-P60S30 and this is my first project / attempt.

    So far I have found a blown cap on the main power supply board.
    After replacing it there's still no standby power.

    Poked around and found a resistor on the PSUB power supply board that measures open.

    An online resistor calculator shows this is a 93k ohm resister.

    My questions:

    Is that correct, 93k ohms?
    Is it a fusible resistor?
    Lastly, how do I know what wattage?...
    05-14-2025, 06:42 PM
  • Lucifer87
    rx 5700 pulse Schematic & Boardview request 1.8 missing sometimes present
    by Lucifer87
    Hi, I need the schematic and boardview of a Radeon RX 5700 Pulse, sometimes it turns on, sometimes it doesn't... I checked when it doesn't turn on, the enable signal is missing on pin 15 EN2 3v to power 1.8v... the problem is that when it works I can't test it since the signal is present... I would like to check the signal paths but I would need the diagram and the boardview thanks​...
    12-15-2024, 12:29 PM
  • Kooopa
    Acer Nitro 5 EC_RSMRST# present, Missing SLP_S5#!!!
    by Kooopa
    Hi! I'm diagnosing my Nitro 5 AN515-43 Mobo: FH50Q LA-J621P. I left it on sleep mode but when I came back It won't turn on. Power LED would turn on for a few seconds then off. no fan spin nor keyboard backlight.

    So I tried the usual procedures first, power cycling and bios reset but non did the trick so I decided to delve deeper.

    Nothing strikes as red flags aside from the dust. there's no history of any liquid being poured at it since I bought the thing, I've been real careful. Anyways.

    I checked the usual rails +5VALW +3VALW even the 1.8VALW and 0.9VALW...
    09-06-2024, 11:38 AM
  • Prott
    Surface 7 - missing S3 sleep signal, S4 present but weird
    by Prott
    Hey fellow Badcappers
    I am troubleshooting Surface 7 board (rev 1.0) which was working great until it experienced a short circuit due to a bad screen.

    Now it's missing SLP_S3 signal. Everything in the power on sequence works properly up until that signal.

    - The resistance to ground on the SLP_S3 line is >50 kOhms.
    - No shorts on any powerrails that I can find.
    - I get a proper clock signal on the RTC crystal (XTAL_2P) once the Surface gets power.
    - SLP_S4 is, suprisingly, present, but it looks very weird (jump up to 2 V for about...
    07-08-2023, 04:54 PM
  • Xrious
    Panasonic TH-55FX600 - No standby LED
    by Xrious
    Got a TH-55FX600 that is showing no signs of life.

    Outputs from the P board look good, but no 12V on the A board.

    Very similar to https://www.badcaps.net/forum/troubl...3e-identidy-ic but where Tibd has 3.3v on the EN pin I have nothing, no voltage at all.

    Looking at the diagram for the IC I can see the enable is W_OPCTRL9, but I can't find a source for this, can anyone help please?

    Stu

    ...
    05-02-2024, 08:56 PM
  • Loading...
  • No more items.
Working...