LG 55UB8500 no picture.

CroBUTKO91

Member

Join Date: Jul 2022

Posts: 22

Country: Croatia
#21

07-30-2022, 03:41 AM

Re: LG 55UB8500 no picture.

you can bypass 12v from mainboard to tcon fuse with wire 12v should be somewhere on the capatitor on mainboard done that to my tv works fine
Comment

Previous 1 2 template Next

Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?

by Tynan Dill

I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

Upon bringing it home and plugging it up, it showed a standby light.

I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

The screen seems to blackout and stay black, but with a flashlight I can see the display.

With my Playstation 4 connected via HDMI, and running a game I can hear sound.

Assuming...

7 Photos
- Channel: Troubleshooting TVs and Video Sources
11-22-2024, 01:46 PM
HP Envy x360 13-bf0013dx (i7, 8gb) ipa32 la-m024p rev 1b short near PJ1802, type-c not switching to 19 volts

by u666sa

Laptop is HP Envy x360 13-bf0013dx, hp website link, it's an i7-1250U with 8 gig onboard ram.
Platform: ipa32 la-m024p rev 1b

Originally you'd plug power supply into it and it would take up to 1.2 amps and then drop to 200 milliamps and then go back up again to 1.2, staying all the while at 5 volts. Pressing power button would results in power LED blinking amber 3 times. 3.3 volt rail, 5.1 volt rail present, main power rail 8.8 volts. Power button test pads near EC chip 2.7 volts.

I found a short on the other side:

...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
10-04-2025, 05:03 PM
12 volt switching power supply modification to 14.5 volts before blocking diode add

by sam_sam_sam

I saw this switching power supply on eBay and wanted to see if could be modified to run 14.5 volts before the blocking diode was add and this switching power supply seems to have no issues doing this

I did recap the switching power supply except the the main filtering capacitors and I managed to break the selector switch for the voltage setting but just jumped it

One note I used 25 volt capacitors on the output side of this power supply because they used 16 volt capacitors and because I am running the voltage up a little bit higher 12 volts to 14.5 volts there would...
- Channel: General Electronics Technical Discussion
04-11-2021, 11:01 AM
No LCD image after connector replacement – lifted components and damaged resistor (Nintendo Switch Lite HDH-CPU-02)

by Tomylee

Hi everyone,

Sorry for the person who’s going to read all this !
I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.

While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.

During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the...
- Channel: Troubleshooting Game Consoles & Other Weird Devices
07-11-2025, 11:52 AM
un60j620dafxza - Samsung No Display Problem

by stylishconsultant

Hi All,

Need help.

I have a samsung un60j620dafxza led tv. When I plug it in it has no display, no sounds, and no standby lights.

So I opened the tv and disconnected the power to the mainboard and the backlight powered up. This according to many people says that this is a mainboard
problem. I checked the voltage coming from the stb and I read 1.3 volts on pins 1,3,5 and 7 which are low volts instead of 13 volts which i think the lcd panel
might be drawing too much power from the power supply that it prevents the right voltage going to the mainboard....
- Channel: Troubleshooting TVs and Video Sources
09-04-2024, 03:26 AM
Loading...
No more items.

LG 55UB8500 no picture.

Comment

Related Topics