Sharp LC-80LE632U 2-5 blink code

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • SdlewisSr
    Senior Member
    • Oct 2015
    • 146
    • United States
    #21
    Re: Sharp LC-80LE632U 2-5 blink code

    I found out from the guys that transported the TV to me that the TV shifted in route and it was the screen coming in contact with a toolbox that stopped its slide. This is likely when the panel was damaged.

      Comment

      • SdlewisSr
        Senior Member
        • Oct 2015
        • 146
        • United States
        #22
        Re: Sharp LC-80LE632U 2-5 blink code

        I raised the panel up just enough to see the screen when the backlights come on and verified that the screen is cracked from the bottom left to the top right (see attached GIF). You cannot see the crack with the backlights off.
        Thanks to all for your help/suggestions.
        Attached Files

        if you find these attachements useful please consider making a small donation to the site

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • advant
            Driving a Sharp TCON/panel with a universal main board
            by advant
            This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.

            I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
            02-03-2020, 12:25 AM
          • moltensolderlabs
            Sharp LC-52E77UN TCON activation WITHOUT motherboard. I2C reverse engineering help?
            by moltensolderlabs
            Hi everyone. [Sorry for the long, detailed post in advance].

            I have a Sharp LC-52E77UN which randomly shuts down--could be within 15 minutes, could be 40 minutes, over 1 hour, it's unpredictable. From reading the service manual, I was able to get into service mode (where the K is displayed), and found the following error flag toggled: "04 Initial Communication Error 4 -- Error reason: To the communication setting reception," which, from contacting an eBay TV repair store, I was told is caused NOT by a bad TCON (which was my first guess), but rather the motherboard....
            10-09-2020, 12:01 PM
          • joblo37pam
            Sharp LC-80LE844U Blinks 2 slow, 5 fast
            by joblo37pam
            It's been a while since I've checked in here or needed input on narrowing down what to replace on a TV repair, but I've got one on my bench now that has me wondering. The lack of part (board) availability means I may need to do some component-level diagnostics, and a second opinion is always good when it comes to that.

            The issue - Sharp LC-80LE844U does not display. Power light comes on for a while, then you can hear a relay click off and the light blinks twice slow, then five times fast. Service manual points to 'Panel Power Supply Error' with this code, but isn't much more help...
            10-26-2023, 02:17 PM
          • ninja_zx11
            Sharp LC-70LE650U vertical black and red bars
            by ninja_zx11
            Hi all,

            70" LED TV is Sharp LC-70LE650U.

            Initial problem was horizontal lines and slow motion lurrs on the bottom left of the screen. So I removed both the left and right ribbon cables from the T-con board and tried to clean it with alcohol and when I put it back, this issue appeared. I tried carefully reinserting the ribbon bon cables but same thing. I checked the traces of the ribbon cables with magnifying glass and everything looks good. I cleaned the small jumper ribbon cable on the left side of the screen which cured the horizontal line and slow motion blurs...
            07-07-2023, 11:27 PM
          • zesko
            xps 9520 ribbon cable
            by zesko
            Hello,
            I have a XPS 9520 with broken daughter board and missing ribbon cable. I can fix the board by replacing the connector, but I can't find the correct ribbon.

            There is 2 models, idk which one is needed on my laptop.

            0xkvng
            00vpr2

            Daughter board is LS H822P. When I check for a palmrest, the board attached to have a 0xkvng ribbon. But when I check for LS h822p, it's 00vpr2 ribbon...

            Someone can help me with that please ? Idk the difference between these 2 ribbon but they definitely doesn't look the same..

            thanks...
            10-23-2025, 05:03 PM
          • Loading...
          • No more items.
          Working...