Sharp LC-80LE632U 2-5 blink code

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • SdlewisSr
    Senior Member
    • Oct 2015
    • 146
    • United States

    #21
    Re: Sharp LC-80LE632U 2-5 blink code

    I found out from the guys that transported the TV to me that the TV shifted in route and it was the screen coming in contact with a toolbox that stopped its slide. This is likely when the panel was damaged.

    Comment

    • SdlewisSr
      Senior Member
      • Oct 2015
      • 146
      • United States

      #22
      Re: Sharp LC-80LE632U 2-5 blink code

      I raised the panel up just enough to see the screen when the backlights come on and verified that the screen is cracked from the bottom left to the top right (see attached GIF). You cannot see the crack with the backlights off.
      Thanks to all for your help/suggestions.
      Attached Files

      Comment

      Related Topics

      Collapse

      • advant
        Driving a Sharp TCON/panel with a universal main board
        by advant
        This thread is about trying to get an Universal Main Board to work with a Sharp TCON and panel.

        I have a Sharp LC-46D85UN TV that has had a main board issue. Since this model is from 2009, I am not able to find an exact replacement of the main board. Instead, I decided to see if I can future proof this tv by getting a Universal Main Board (T53U21.2) from China to work with the Sharp TCON (CPWBX4291TPZA) and panel. The universal main board supports a 8 bit dual channel LVDS interface whereas the TCON requires a 10 bit dual channel LVDS input. I have modded the LVDS connector to match...
        02-03-2020, 12:25 AM
      • moltensolderlabs
        Sharp LC-52E77UN TCON activation WITHOUT motherboard. I2C reverse engineering help?
        by moltensolderlabs
        Hi everyone. [Sorry for the long, detailed post in advance].

        I have a Sharp LC-52E77UN which randomly shuts down--could be within 15 minutes, could be 40 minutes, over 1 hour, it's unpredictable. From reading the service manual, I was able to get into service mode (where the K is displayed), and found the following error flag toggled: "04 Initial Communication Error 4 -- Error reason: To the communication setting reception," which, from contacting an eBay TV repair store, I was told is caused NOT by a bad TCON (which was my first guess), but rather the motherboard....
        10-09-2020, 12:01 PM
      • joblo37pam
        Sharp LC-80LE844U Blinks 2 slow, 5 fast
        by joblo37pam
        It's been a while since I've checked in here or needed input on narrowing down what to replace on a TV repair, but I've got one on my bench now that has me wondering. The lack of part (board) availability means I may need to do some component-level diagnostics, and a second opinion is always good when it comes to that.

        The issue - Sharp LC-80LE844U does not display. Power light comes on for a while, then you can hear a relay click off and the light blinks twice slow, then five times fast. Service manual points to 'Panel Power Supply Error' with this code, but isn't much more help...
        10-26-2023, 02:17 PM
      • ninja_zx11
        Sharp LC-70LE650U vertical black and red bars
        by ninja_zx11
        Hi all,

        70" LED TV is Sharp LC-70LE650U.

        Initial problem was horizontal lines and slow motion lurrs on the bottom left of the screen. So I removed both the left and right ribbon cables from the T-con board and tried to clean it with alcohol and when I put it back, this issue appeared. I tried carefully reinserting the ribbon bon cables but same thing. I checked the traces of the ribbon cables with magnifying glass and everything looks good. I cleaned the small jumper ribbon cable on the left side of the screen which cured the horizontal line and slow motion blurs...
        07-07-2023, 11:27 PM
      • Tr0ll
        T-con suspect issue. Both ribbon cables no picture. One ribbon cable ok. (58pus8545)
        by Tr0ll
        Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.

        The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.

        Original T-con:
        Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.

        First replacement T-con:

        I thought it might be t-con and ordered new t-con from china(supposedly tested)...
        10-07-2023, 07:48 PM
      • Loading...
      • No more items.
      Working...