Help Diagnosing Backlight Voltages (JVC LT-50C550)

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • Shotgun25
    Senior Member
    • Feb 2014
    • 90
    • UK
    #21
    Re: Help Diagnosing Backlight Voltages (JVC LT-50C550)

    Originally posted by dick_barton
    You can share on the "EEPROM Dump Thread" which is the first thread on the forum.
    If the file is too big to upload then you can Winrar it into smaller chunks.
    OK thanks, only just seen this, I should have subscribed to the thread
    It is massive, I'll go check out the preferred hosting that others are using and upload and share.

    EDIT: Uploaded here https://www.badcaps.net/forum/showpo...postcount=1033
    Last edited by Shotgun25; 09-03-2021, 01:23 PM. Reason: Added link to firmware

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • Capacitorial
        Powersupply has all the voltages - Monitor still no power
        by Capacitorial
        Hello guys,

        I have a Philips 240B7QPJEB. The monitor seems completely dead.
        I opened it and measured the voltages of the powersupply. I found that a mosfet was dead and replaced it.
        On the connector, that goes to the TCON board, all voltages 15-19V and 5V are present.
        The small connector on the left of the PSU has two cables with 18V and all the other have 0.2V. It connects on this small connector on the left ontop of the panel. I guess the backlight? Seens fine I guess.
        The weird thing is, that the Power LED is powered over the TCON board.
        On The TCON...
        12-28-2024, 02:12 PM
      • Pipolups
        Corsair K70 LUX RGB dying LEDs
        by Pipolups
        Hi there !

        I'm having an issue for several weeks with my quite old K70 LUX RGB keyboard. I haven't used it for few months, and once I setup up again my desktop computer, I got several dead LEDs on that keyboard. I tried the Corsair troubleshooting thing (disabling options in iCUE, ...) but nothing changed so I conclude that for some reason some LEDs went in retirement...😅
        Decision taken to change these LEDs as I have access to desoldering iron and binocular magnifier, I wrote a ticket to tech support, hopping to obtain the LEDs reference and... They refused to tell me 🙄...
        10-08-2024, 11:58 AM
      • THE GTC
        Insignia NS-37D20SNA14 intermittent LEDs
        by THE GTC
        So I use this TV daily as a second monitor for my PC or my Playstation - at one point a few months back I tried to fix the problem - but in the process, I figured out something that works so I haven't posted this for awhile. It is an annoying trick to have to do though, so I decided to post about it to see if anyone could spot what's wrong. It baffles me because it works on it's own half the time.

        When I first got this TV, I was told it wouldn't turn on, and of course I did the flashlight test, and the image was there. Also, the red LED on the front indicated that it had power (it...
        11-03-2020, 02:40 AM
      • Rank73
        Samsung PS51E450A1W
        by Rank73
        Hi all.
        It's a great place you've got here. I've learnt a lot in the last couple of days researching my problem and diagnosing this tv. It's a Samsung PS51E450A1W with no picture. Here are the symptoms and what I've tried. Any help is hugely appreciated.

        symptoms:
        No picture
        No chime on start. (maybe turned off?)
        Powers on, small flash of screen, 5 slow red leds on the front, at the same time: 1 slow and 14 long on the green led on the logic board. Then reboots and does the same.

        The sticker with the voltages are:
        VA 58
        ...
        07-13-2023, 03:42 PM
      • gjgib
        Help reading schematic voltages input/output
        by gjgib
        Hello, this might be embarassing since I consider it a dumb question but keeps me kinda stuck sometimes in my journey.

        I want to know if there is any post in this forum which explains my questions. A) When, where and how do I know when X voltage line is input or output. Example:


        I'm battling with this IC to understand it's voltages. It's from non-turning-on Lenovo Ideapad 3 15iil05 - NM-D461.

        I see some lines like +5VL / +5VALW / V9B+ / +3VALW being okay and some others like 1.8VALW / +0.6VS / +2.5V_DDR. I just know that some of them are bad or missing,...
        05-06-2024, 08:11 PM
      • Loading...
      • No more items.
      Working...