LG 55EC930v Panel dead???

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • AdrianMutu
    New Member
    • Sep 2019
    • 2
    • Roamnia
    #1

    LG 55EC930v Panel dead???

    Hello guys,
    In both a defect LG55EC930v with the hope to repair it but till now no success.
    The Panel looks perfect it has no cracks or other deterioration. The Tv starts and after 2s turns off no image just black. After reading some Posts i i understood how to check the PSU and the Values look ok, did the checks like in the service manual with light bulb and all was ok. After reading the Posts from freakaftr8, Billsy and Diah i bought a Service remote to get out of the protection mode and i could start it for 1s and received the image in the Photo.
    Could you tell from it if the panel is broke? The left corner is black.
    I appreciate any help or suggestions.
    Br,
    Adrian
    Attached Files
    Tags: None
    • Diah
      Badcaps Legend
      • Feb 2013
      • 6384
      • Germany
      #2
      Re: LG 55EC930v Panel dead???

      post please photo on yours T-CON driver boards.
      also unplug the first right ribbon cable ( when you look at the set from back side )which it goes to panel. inspect its pins from both side. keep it out and tun on yours TV and immediately press power on RC check if the set goes to stand by mode...

        Comment

        Previous template Next

        Related Topics

        Collapse
        • KYBOSH
          Samsung UN50TU8000 - Dead Panel Forensic Questions
          by KYBOSH
          I came across a 50inch TU8000 that wouldnt start up properly (blinking stand-by light, backlights would cycle on and off).





          When i opened it up and removed the power to the mainboard the backlights powered up and everything looked uniform.
          When reconnected the mainboard but disconnected the flex cable to the panel i heard the TV startup with the intro sound.






          Later I checked for shorts on the panel PCB boards but could not find anything.
          When I took a look with the FLIR i noticed the 2 resistors...
          08-10-2024, 08:39 AM
        • NSkyLab
          Vizio D43f-J04 is panel dead?
          by NSkyLab
          TV Model: Vizio D43f-J04
          Main Board: TPD.MT5583.PB751 (60103-00876)
          T-Con: BOE_CC430LV2D_43001 V1.0
          Panel: BOEI430WU1

          The video of the defect is here: https://photos.app.goo.gl/fzfvmUqGXW3c1Nrg9
          This is a dumpster find, don't know if it was hit, there are no visible cracks...

          I though there may be something wrong with the panel voltages.
          Those I managed to find on the T-Con board. Does it seem normal?
          12V: 12.27v
          VCC33: 3.28v
          1.2V: 1.25v
          VGL: -5.87v
          AVDD: 16v
          HAVDD: 7.47v
          VCOM: 7.0v...
          01-29-2023, 08:18 PM
        • howardc64
          LG 49UJ6500 LCD panel lighter band that goes away
          by howardc64
          49UJ6500 LCD panel has a lighter band on top when first powered on. Goes away (or gets much fainter) after TV on for a few min. After powered off for awhile and power back on, same band appears. If powered on immediately after powering off, no or much fainter band. Running the latest firmware.

          Disassembled the TV and lifted the LCD panel during testing. Band is on the LCD panel (can see the band on the panel as I lift it slightly) Backlight is perfectly even at the top edge. Double checked LCD panel alignment in the frame and is perfect but since band moved with the panel, its on...
          02-19-2023, 12:13 AM
        • triplefour
          SAMSUNG UN50TU8000F rebooting, backlight ok. No 12v to panel boards.
          by triplefour
          TV flashes backlight then reboots over and over. no image. Client said it used to have image for a bit before rebooting. Got worse over time.

          tcon is built into mainboard.
          Only one cable goes to panel boards.
          there is a cable from one panel board to the other that links them.
          cost cutting measure that results in us having harder time to diagnose.
          removing the link to the second panel board allows TV to stay on with stable backlight but no image.
          used cut off tape method to mask 1 maybe 2 pins on the side of the cable that goes to that second panel board....
          07-28-2022, 07:59 PM
        • Storyteller12
          QN55Q60R Service Menu Panel Help
          by Storyteller12
          I had a the above tv qn55q60r that had a bad panel but everything else good. I had another panel here from un55nu6900 with bad leds and melted diffusers.

          I put the nu6900 panel in and powered it up and it does work but there are lines vertical lines.

          I was trying to change the panel type in the service menu but don’t see my exact panel. Anyway to fix this or someone have similar experience.

          the clear picture is the panel type from the service menus on the nu6900. The other 1 is the panel type that was set for the q60r with the bad panel....
          01-13-2024, 01:57 PM
        • Loading...
        • No more items.
        Working...