Quick question

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Demonata08
    Senior Member
    • Jan 2019
    • 116
    • USA
    #1

    Quick question

    Got a plasma with vertical lines. bought it hoping it was just a buffer board but i took it apart and found a small hole in the ribbon cable going from the panel to the buffer board.

    I feel this one is destined for recycle but i just have to ask if anyone knows a way to fix this problem. Every single ribbon cable on the panel has adhesive that has completely failed which is why i think this problem happened to begin with but thats easily fixable.

    Damaged Cable
    Tags: None
    • tvtimmy
      Badcaps Legend
      • Mar 2015
      • 1160
      • usa
      #2
      Re: Quick question

      Scrap it out. It can't be fixed. What is the model number of the tv?

        Comment

        • Demonata08
          Senior Member
          • Jan 2019
          • 116
          • USA
          #3
          Re: Quick question

          Pn42a450p1d

            Comment

            Previous template Next

            Related Topics

            Collapse
            • howardc64
              TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
              by howardc64
              All left and right refers to looking from rear of TV (or looking from front with TV upside down)
              • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
              • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
              ...
              07-24-2025, 05:17 PM
            • Rubenlily
              Quick question about the ribbon
              by Rubenlily
              Hey,

              So I have horizontal lines on my TV and I'm trying to trouble shoot. My question about the ribbon is:

              When I disconnect one ribbon from the t-con I should get half picture working and other half black or something like that correct? But when I disconnect the ribbon on one side I just get a dark screen and it doesn't matter what side I disconnect. I just get the dark screen. No half working, no one half black and the other one left. Sound is playing from the TV so it's obviously on and when both sides are connected I have the picture with the horizontal lines...
              08-17-2023, 11:09 AM
            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • Tr0ll
              T-con suspect issue. Both ribbon cables no picture. One ribbon cable ok. (58pus8545)
              by Tr0ll
              Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.

              The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.

              Original T-con:
              Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.

              First replacement T-con:

              I thought it might be t-con and ordered new t-con from china(supposedly tested)...
              10-07-2023, 07:48 PM
            • Yanleb
              Schematic or datasheet for Plasma TV buffer chip
              by Yanleb
              Hi all,

              I'm interested in understanding how a buffer board chip is working. I know there's about 90 outputs per chip to the plasma panel, but I'm more interested to know about the input pins. I guess that some of them are address pins, but I want to know more.

              So far I've found nothing at all. I haven't found any datasheet about the various buffer chips, and I haven't found any schematic for the buffer board using them (Y Buffer Board in Samsung's terminology).

              Any information will make me happy. It can be from any buffer chip or plasma TV manufacturer....
              05-18-2022, 01:36 PM
            • Loading...
            • No more items.
            Working...