mosfet mdf13n50

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • chrislyons
    Member
    • Apr 2018
    • 39
    • United Kingdom

    #1

    mosfet mdf13n50

    hi there i have vestel board shorted out blown fuse, i do have some knowloge repairing tvs ,using meter thanks to sites like thism,ok i found two mosfets shorted, mdf13n50. looking in my box i can i can only find 13nm60n ,mosfet that 600,v is there chance messing the set up with this sort, ?
  • R_J
    Badcaps Legend
    • Jun 2012
    • 9514
    • Canada

    #2
    Re: mosfet mdf13n50

    Check and compare the data sheets, a quick look says the 13nm60n handles a couple amps less current but otherwise should work. You should also check the gate drive circuit, resistors etc. and it is also possible the drive ic's output could be damaged, post pictures or at least model of tv, power supply board number etc.
    Usually if the fets are shorted there could be source resistors (if used) open also
    They should work to test the power supply but its best to use the same or better fets for best operation
    Last edited by R_J; 01-27-2019, 04:22 PM.

    Comment

    Related Topics

    Collapse

    • Nooy
      VGA MOSfet permanently shorted and loss of MOSfet pad
      by Nooy
      Hello everyone, I recently found this badcaps site and super Learn Electronics Repair youtube channel. And I wanted to learn how to troubleshoot power supplies and VGA cards and how to practice soldering, since I already have a properly defective piece of them. I am currently trying to solve two problems:

      I have a Gigabyte GV-RX460WF2OC-4GD type card. I managed to find the faulty MOSfet (AON6414A) on it, which I replaced. The card starts up, but after about half a minute, the MOSfet in the same position will be shorted again. Is it possible that the PWM controller driving the MOSfet...
      02-14-2024, 02:26 AM
    • chestercc
      Alienware M18x Shorted CPU Mosfet
      by chestercc
      I've got an old Alienware M18x R1 which shorted out the charger whenever it was connected. Tracked down the short to two shorted caps and burned CPU power controller caused by a shorted mosfet on the CPU's graphic power supply.

      I've replaced the faulty mosfet, two shorted caps and the CPU Power controller (NCP6151S52MNR2G).

      Issue is now whilst there is no short if I attempt to power the system on the fans spin for a couple seconds there are no lights and no further action - the PCH is heating up but there is no CPU power coming out but there is an enable signal...
      07-16-2022, 06:05 AM
    • mat2k
      iMac 2017 PSU - shorted PFC mosfet
      by mat2k
      I am trying to fix an iMac 2017 PSU, initially came with a blown fuse and shorted PFC MOSFET (6R199P). After visual inspection and some measurements I replaced the FET with a P20NM60 and tested with 100w series lamp, and it lasted 1 second before going into dead short. The PFC controller chip (NCP1605BG) and its passives appear fine (passives measure OK), but I do not know if there is a simple way of testing the NCP1605 as I wouldn't like to blind-replace it.
      There was some slight blackening of the solder on the PFC controller passives so I reflowed them all with some flux. I am waiting...
      03-13-2025, 11:31 AM
    • daemon123
      MSI GTX-980ti shorted MOSFET on memory rail
      by daemon123
      Hi All,
      I have this MSI GTX-980ti Gaming Golden Edition. It had shorted mosfet on memory. Replaced the shorted i.e. Q47 PK616BA with 4C09N and the card ran fine for a month. Then suddenly again the same problem. This time when i replace it 4C09N or with replacement PK616BA (Aliexpress) it gets shorted. As soon as turn on the PC the PSU shuts down and the same mosfet Q47 gets short.
      What should be the next step. Kindly guide.
      The board view files for this gpu is available and attached. https://www.badcaps.net/forum/showthread.php?p=1237952...
      05-10-2023, 11:05 AM
    • Jane
      How do you test MOSFET in laptops ?
      by Jane
      I tried to use this method:

      Testing an N-channel MOSFET:

      Step 1: Discharge the Gate (turn off the MOSFET)
      Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
      Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

      Step 2: Charge the Gate (turn on the MOSFET)
      Now, place the red probe on the Gate (G) and the black probe on the
      ...
      09-27-2024, 03:31 AM
    • Loading...
    • No more items.
    Working...