Hi, initial fault: sometimes it doesn't power on, after a CPU reflow attempt it no more boots, i come fast to conclusion, i need help of some one also with the 42" model or some similar family model like 6007,7007,8008 series that is able to save the content of the settings eeprom and give me this file and its option table written on the back of tv. Help is highly appreciated! Please do a good action, i'm stuck on this tv since 1 year and half. I'm near to set it on fire.. bye.
-
-
Re: Philips 47pfl6008s level 2 blinks 53 after reflow
I know the problem is the cpu soldering. Must to take some time to make experiments more on reflowing / reballing, the problem is widely common.Comment
-
Re: Philips 47pfl6008s level 2 blinks 53 after reflow
NVM software for a QFU1.2. After programming the options etc must be aligned.Comment
-
Re: Philips 47pfl6008s level 2 blinks 53 after reflow
I have two lcd panels Philips 40pfl7007t12 and 46pfl7007t12.On the first panel i was changed ssb of the second panel.Now i have 40pfl with ssb of 46pfl!now i have a problem with switching on, but after re-flashing eeprom with service dumps,i can switch on the tv only fist time!What do you think about this problem&Comment
-
Re: Philips 47pfl6008s level 2 blinks 53 after reflow
It's obvious, why to take an unknown dump from somewhere and not to read the data from the original board and put it on the replacement one? But DON'T HIJACK OTHER ONE's THREAD! Open up your own one and discuss there.. Don't reply please!Comment
-
Bought this TV used not working, panel flashed briefly on power up and it was blinking 8 times, a quick look on SS board revealed a common fault on the 3uF 250V capacitors, C201 to C205 (C1620X in the service manual), the solder joints were all cracked, C201 and C205 pins were darkened and some sparking had occurred on them, C201 was split open and clearly overheated in its last hours, replaced that one and resoldered the others, 8 blinks fixed.
Also the previous owner broke the antenna connector by taking the TV out of the wall mount forgetting to unplug it, I desoldered the tuner... -
Hello all,
I am experimenting a bit with reflowing larger components - ideally I'd like to reflow a PS4 APU or a GPU for example.
I know it's impossible to reflow such large components with just hot air so I bought a pre-heating plate, T-8280 classic Chinese machine, which seems to be working fine besides it's a little slow, which shouldn't be a big deal.
Now, my hot air station is a Aoyue 852A++ and I feel it's a bit weak when used with larger nozzle. I tried reflowing a laptop chipset using one of those large, rectangular, nozzles and I failed miserably,... -
Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.
It does power up when pressing the power button.
I already try the power button while plugin the plug with no result.
Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.
Could this be an PSU or eMMC issue ? -
Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.
TV Model: Panasonic TC-P55ST50
...11-20-2024, 08:52 PM -
Does anyone have an idea of what might be the issue with my 3050 micro? I have tried replacing new cmos battery but still the same
I am not sure if its the powersupply that I'm using is the issue since its the original powersupply. its a laptop powersupply with the same specifications with the 3050 micro so i guess it should be fine.
i also tried replacing the bios but with no avail, everytime i try another bios it gives a different blinking lights
Any recommendation on what I have to do next? Thanks in advance
Comment