William1967
Badcaps Veteran
Last Activity: 04-22-2025, 02:28 AM
Joined: 11-08-2017
Location: Eindhoven
-
How did you performed the factory reset? -
Try to run the upgrade_loader.pkg to reset the EMMC files, if that does not help there are lots of things that can go wrong that can cause a reboot. The EMMC could also be at it's end of life, seen that a lot of times with these mainboards.Leave a comment:
-
I have seen that very often.
Sometimes repairable with a little piece of tape but what sometimes appeared was a spot with less red than normal or thin lines running through the image from left to right.
Sometimes clearly visible but sometimes not.
The Panda panels are bad and come in many brands but especially the 58 inch is very bad....Leave a comment:
-
This has nothing to do with software/firmware. This is a panel problem, try to block some datalines with some tape and the problem will be solved. The 58" with a Panda panel is known for this problem.Leave a comment:
-
Unfortunately there are no diagrams for this power supply, they were completely replaced.
There are 2 power supplies that can be used 272217100749 and 272217190104.
One of the two broke down quite quickly, the other is an improved version, unfortunately I don't remember which of the two was the improved version.Leave a comment:
-
This is a completely different power supply, it is best to create your own topic. What is the 2722171xxxxxx number on your [cb?...Leave a comment:
-
The tv has an so called OPEN CELL panel/t-con, it goes in WBRG mode when there is 12V on the t-con but no data from the mainboard. Check the LVDS cable if there is no damage and check if there is data comming from the mainboard.Leave a comment:
-
Type 062596 MENU(HOME) or 062596 OK on your remote to enter the service menu.Leave a comment:
-
Update is possible via USB, search for 32PFL3403/D firmware with Google or similar searchengine.
If you want to switch of the shop mode Press MENU on the remote control and select TV Menu > Installation > Preferences > Location....Leave a comment:
-
@ [B][URL="https://www.badcaps.net/member/596229-primozd"]Primozd[/URL][/B], Maybe this will help. There is no 028 option for a 55PUS7506/xx@ [B][URL="https://www.badcaps.net/member/596229-primozd"]Primozd[/URL][/B], Maybe this will help. There is no 028 option for a 55PUS7506/xx@ [B][URL="https://www.badcaps.net/member/596229-primozd"]Primozd[/URL][/B], Maybe this will help. There is no 028 option for a 55PUS7506/xx...
Leave a comment:
-
First check the screencode. Press 062598 menuXXX on your remote, after the code is accepted the TV should go in stand by, if not try again. XXX is the screencode that you can find on the rear cover....
Leave a comment:
-
See here....
Leave a comment:
-
I always use a USB with control led to see if there is activity.Leave a comment:
-
What is there to explain, a Philips oled tv the tv goes into t-con protection if an error is "seen" that is panel related. This can already be due to dirty cables or cable connections, you can clean these with compressed air and IPA.
A thin line in the dispaly also could be a culprit.
To remove the t-con error you need special software, this is a small 20kB file that overrules the error....Leave a comment:
-
When the red led on the front is flashing very fast the TV is in t-con error, with a small piece of software that error can be deleted and the tv will start....Leave a comment:
-
As mentioned before, check the leds. That the leds work for a short time is possible, had that before.Leave a comment:
-
You should check the LED strip, that's often the fault. One ore more leds come loose or just die.Leave a comment:
-
Additional information: Standard this tv is not an Android, that upgrade_loader only works when there is an upgraded mainboard inside. The original mainboard has a white ceramic cooling block, the upgaded verion has a metal cooling block...
Leave a comment:
-
Check the smd capacitors on the t-con, maybe one is s/c.Leave a comment:
-
Reloading the firmware (upgrade_loader) also makes little sense if there is no image. Then you would benefit more from resetting the Setoption, even though in this case it seems to me that the panel has a problem. Measure whether the t-con receives 12V and then you can measure some voltages on the t-con. An important one is the 15V to the panel.Leave a comment:
No activity results to display
Leave a comment: