Need Help Locating Resistor

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • audiofreak19
    Badcaps Veteran
    • Apr 2013
    • 556
    • usa

    #1

    Need Help Locating Resistor

    I have a blue resistor that looks like the ceramic capacitors that I need to replace. I cant find it on mouser or digikey. It has in writing R. then below it says 331K and below 1kV. I will try to post a picture if I can. Can anyone help locate a replacement?
  • neilc6
    Badcaps Legend
    • Nov 2015
    • 1550
    • Canada

    #2
    Re: Need Help Locating Resistor

    330pf 1000V ceramic capacitor. You can get at digikey.

    https://www.aliexpress.com/item/100p...683422162.html

    Comment

    • audiofreak19
      Badcaps Veteran
      • Apr 2013
      • 556
      • usa

      #3
      Re: Need Help Locating Resistor

      Son of a gun... That's it. I was way off. I thought the 331k ment resistance or that the R. was for resistor. Thanks for your help. I really appreciate it.

      Comment

      • CapLeaker
        Leaking Member
        • Dec 2014
        • 7964
        • Canada

        #4
        Re: Need Help Locating Resistor

        while you're at it, replace it with a higher voltage rated one. Digikey part number: 445-16023-ND

        Comment

        Related Topics

        Collapse

        • jinu_j
          Dell 2209WA - power supply - Fusible Resistor replacement
          by jinu_j
          Hi

          I am trying to repair an ancient Dell 2209WA Monitor which suddenly shut off with a pop sound. On investigation found that one of the fusible resistors had blown. Further investigation identified multiple components as faulty because of which the fusible resistor blew. Please refer the attached circuit diagram showing the components that were found to be damaged.

          1. FR950 - blown fusible resistor - 0.2 Ohm 1W
          2. Q950 - shorted Q950 MOSFET - 650V 10A N Channel Mosfet
          3. R835 - Blown Resistor - 20KOhm SMD resistor
          4. D930 - Shorted Schottkey Diode...
          05-03-2025, 10:51 PM
        • mikey5791
          Need help to replace burned resistor in 350w atx psu
          by mikey5791
          Hi to all forum members,

          Got this faulty 350 watt atx psu dirt cheap from a local online seller as i am keen to use it as a learning tool to repair faulty power supply.
          The faulty part is quite obvious from the burn area near the 16pin KA7500 BD pwm. The fuse is still intact with good continuity.

          Upon power on ac, there is 5vdc standby power on cathode of diode D14 and about 10vdc on cathode of diode D13.(This should be the aux power to generate the 12v and 5v rail.)
          Initially i replace the two burned resistors near my marked red arrow to 200 ohm resistor...
          12-26-2024, 04:55 AM
        • MidnightRoller
          Can a resistor lose resistance after hot air?
          by MidnightRoller
          I am curious if a 0402 resistor could go from 43 ohm to 0. In electronics class and my experience a resistor can degrade and gain resistance all the way up to not being able to conduct at all. I have never heard of a resistor decreasing in resistance and becoming 0 ohm or a dead short… that's not the direction they fail… or so I thought.

          I was attempting to remove a wson8 chip on an iMac motherboard and it required a lot of heat, on one side of the chip were 3 0402 resistors that were very close. I popped the chip out unintentionally out of the tweezers and sent those resistors...
          02-02-2022, 11:46 PM
        • artvandalai
          What resistor ohm will work better to repair this waterpik?
          by artvandalai
          The resistor on this waterpik blew. I changed it with the a similar spec 47ohm 2 watt yageo resistor but it still keeps blowing the resistor. Checking with the multimeter the motor, capacitor, diodes, and thermal fuse all checked normal. Will a higher ohm resistor work better? What ohm resistor will work better to repair this waterpik? This video is showing the repair with a 56 ohm resistor https://www.youtube.com/watch?v=_J7_rV7ui1Y
          01-05-2025, 04:10 PM
        • chth96
          Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
          by chth96
          I have purchased an 100-240v AC/5v 2a DC adaptor from aliexpress,and a month ago It smelled burning when I plugin it powerstrip.
          Since then, This AC/DC adaptor have been out of order.
          But A few days ago,I replace 0.5 watt resistor with 1 watt resistor(1ohm) in this adapter.
          After replacing resistor,It succeed to recharge all of android phone.And When I measure voltage on the two pins of USB port,It shows 5.5v
          Is it okay to replace 1/2 watt resistor with 1 watt resistor in AC/DC adapter?
          And Is there any possibility that it will suddenly explode as well as to be out...
          12-03-2023, 04:40 AM
        • Loading...
        • No more items.
        Working...