panasonic tc-p50s60 bricked after firmware update?

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

They should take care of you, as i have yet to get anything junk yet from them but it is possible.

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

yeah it is found this one and will work have yet to get anything bunk from them.
http://www.tvpartstoday.com/TXN-A1US...sh-a1usuus.htm


Little pricey but will stop the woes, get a refund on the bunk one.

That's where I got the new A-Board in the first place, it was the last one in their stock when I ordered it a couple weeks ago.

You have to call them to set up a return, I might do that tomorrow or at least see if they will exchange the A-Board I purchased for the one they have in stock now.

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

yeah it is found this one and will work have yet to get anything bunk from them.
http://www.tvpartstoday.com/TXN-A1US...sh-a1usuus.htm


Little pricey but will stop the woes, get a refund on the bunk one.

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

I appreciate everyone's help and suggestions in this thread, getting into the EEPROMs and Integrated Circuits and going down to that level has me a little overwhelmed, and is a rabbit hole of research to understand all of it.

http://www.shopjimmy.com/panasonic-t...-tc-p50s60.htm


Is that same as yours part number and all? i'll see if i can find you an A board

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

if they're indeed same exact board yes it is possible, but it would make more sense to copy the bin from it and transfer it to the other rather than butcher possibly good board, but then again we don't know if it's rom er bin is corrupted or not which may very well be the reason replacement not working.

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

Think you're gonna need one of these and flash original back.


https://www.ebay.com/itm/USB-BIOS-EE...ss!49457!US!-1

Since I have two A-Boards, wouldn't it be possible to just swap the chip from the "new" board I got into the old one that I know is bricked? If the new A-Board I received is indeed faulty, perhaps the one part (an IC?) I need from it isn't? Since I would most likely have to source the bin from the new board I got anyway(I don't know how easy it would be to find online), would it be easier to just swap the ICs?

Looking at these boards, none of these chips look removable, at least not for a novice like me - but if an IC swap on the main boards seems like a plausible solution, I could bring the boards to a local professional to do it for me.

I appreciate everyone's help and suggestions in this thread, getting into the EEPROMs and Integrated Circuits and going down to that level has me a little overwhelmed, and is a rabbit hole of research to understand all of it.

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

Think you're gonna need one of these and flash original back.


https://www.ebay.com/itm/USB-BIOS-EE...ss!49457!US!-1

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

Why did you originally update the f/w in the first place?

--What faults indicated to you to go to that extreme?

Regardless of what makers say, when updating f/w there's always a possibility of bricking it--no matter what the thing is, let alone TV sets with their multitude of different versions--Of the same set!

Route of last resort in my book, leave f/w alone unless you know for sure its the cause of the problem, and if there IS NO Problem, defo dont do it--don't even think about it!

It was a silly reason, that I deeply regret now that I've possibly bricked the TV. I was having trouble getting the TV to recognize my network's media server, and figured updating the firmware couldn't hurt.

That being said, for most of the time I've owned this TV, I haven't even had the internet options turned on. I had a roku3/cable box/pc all hooked up to this TV through an Onkyo receiver so I never really ever used the few built in apps/features that this early smartTV has... I was wanting to move the roku to a different room with an older TV.

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

Can you take a clear picture of the SC board? Especially the bottom left area , is there a SC50 jumper? ( between 2 white connectors )

If so , remove the 2 buffer boards or make sure they DONT touch the sc board. Use a harddisk jumper or something else and short the 2 pins. Turn on the tv and see if it stays on.
What it does is turning on the tv without sending a image to the panel. If it stays on you got bad buffer boards.

If the 6 blink error stays on BOTH sc boards your problem seems to be the mainboard. I will look in the service manual when i get home.

Let me know what the outcome is!

I found an old hard drive jumper and wedged it into the SC50 jumper (it wasn't easy to get the jumper in there, like it was just a little bit too big)


The result was the same 6 blinks. I haven't tried my original SC board yet, that's next. (edit: I put the original SC board back in, with the jumper, and got the same 6 blinks)

If the TV Stays on with no signal being sent from the buffer boards.... how will I know? Will I be able to pull up the onscreen menus and such?

[Alastair E]

Re: panasonic tc-p50s60 bricked after firmware update?

Why did you originally update the f/w in the first place?

--What faults indicated to you to go to that extreme?

Regardless of what makers say, when updating f/w there's always a possibility of bricking it--no matter what the thing is, let alone TV sets with their multitude of different versions--Of the same set!

Route of last resort in my book, leave f/w alone unless you know for sure its the cause of the problem, and if there IS NO Problem, defo dont do it--don't even think about it!

[Moreno83]

Re: panasonic tc-p50s60 bricked after firmware update?

Ps , with the old mainboard installed im sure you tried the power button on the remote itself? It wont come out of standby with the power button on the tv or other buttons.
Also double check the SC20 cable , release both hatches and pull them open untill they cant go any further. Take the SC20 connector and slide it in. Maybe clean the sc20 cable wih some alcohol and look inside the connector.

It happened to me once that i had a faulty sc20 cable due to heat/dust etc

[Moreno83]

Re: panasonic tc-p50s60 bricked after firmware update?

You should not have bought the sc board to be honest. I get it , you want the tv to be working again but dont go buy random boards. Waste of money.
Just looking at the picture you provided i think you received a bad A board ( mainboard ). But that is just a guess.

Can you take a clear picture of the SC board? Especially the bottom left area , is there a SC50 jumper? ( between 2 white connectors )

If so , remove the 2 buffer boards or make sure they DONT touch the sc board. Use a harddisk jumper or something else and short the 2 pins. Turn on the tv and see if it stays on.
What it does is turning on the tv without sending a image to the panel. If it stays on you got bad buffer boards.

If the 6 blink error stays on BOTH sc boards your problem seems to be the mainboard. I will look in the service manual when i get home.

Let me know what the outcome is!

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

Should be good then. Formally tristate module. i have yet to receive anything bad from them, anything but it is possible to get a bad part but i can tell you they have called me before they shipped an order of multiple parts to let me know one was damaged and failed test so the order had to be modified.

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

tvpartstoday.com

Same place I got the A-board

[heavymachines]

Re: panasonic tc-p50s60 bricked after firmware update?

Where did you get the board?

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

Update : got the new SC Board, installed it. Still getting 6 blinks. I tripled checked all the connections and screws before I even plugged the thing back in.

I'm all out of ideas on what the issue could be. Really don't want to go in on more parts (the SU and SD Boards).

Also about all out of patience, guess I'm going to start looking into new TVs.

[koka0011]

Re: panasonic tc-p50s60 bricked after firmware update?

i guess you need to re-flash the ROM ic.find a programmer and re-programme tha ROM ic.
RT809F or RT809H (find the bin file)

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

try the old a board back in .

Tried that as well, and got the original result. With the old A-Board the red LED just comes on and stays on, never blinks. TV Still doesn't work.

[petehall347]

Re: panasonic tc-p50s60 bricked after firmware update?

try the old a board back in .

[mushchampion]

Re: panasonic tc-p50s60 bricked after firmware update?

I went ahead and ordered the SC Board, I figure what's another $30(45 w/ shipping) if it saves me buying a new tv. I really love my Panasonic Plasma, and I got it for next to nothing from Sears shortly after Panasonic announced they wouldn't be making plasmas anymore.

I'll update again next week when I get the new SC Board.