Element 40" TV

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • don250r
    New Member
    • Jul 2017
    • 5
    • USA

    #1

    Element 40" TV

    Hi folks.
    Today i bring you a Element ELDFW406.
    Lightning strike early AM of 7/3, took out 4 TVs and 4 cable boxes.
    The only "survivor" is the Element TV, as it was farthest away from strike.
    However, when powered on, i get only the front blue light indicating it is turned on. No splash screen, no apparent backlight. Tried checking for backlight issues with a darkened room and a flashlight to no avail.

    Opened her up, and checked power supply board voltages. I get a 5, 12, and a 24, and i THINK i got a 3 something(will check again tomorrow). My question is this: Should i be getting anything other than 5,12, and 24?

    So far, im thinking maybe main board, but any and all input will be appreciated.
    BTW, did a visual inspection of all caps, none appear to be busted, bulging, etc.
  • attainteddragon
    Badcaps Veteran
    • Apr 2013
    • 764
    • australia

    #2
    Re: Element 40" TV

    main board is the most common failure with surges. you can jump the power supply on with a couple of 1k resistors to confirm that the ps is ok.
    WHY CAN'T PHILIPS USE PHILLIPS HEAD SCREWS?

    Comment

    • dskall
      Badcaps Legend
      • Oct 2016
      • 2905
      • usa

      #3
      Re: Element 40" TV

      Need good clear straight on pictures of back of tv with cover off and each board.


      Need voltages from connector that goes from power supply board to main board. Will need pin#- PIN DESCRIPTION -Pin voltage in standby-Pin voltage when pushing power button and picture of connector on power supply board.
      Format:
      Pin# - Pin Description - Pin Voltage standby - Pin voltage power on
      1 - XXXXXXX - XXv - XXXv
      2 - XXXXXXX - XXXv - XXXv
      3 - XXXXXXX - XXXv - XXXv
      4 - etc.
      I assume no responsibility for any stupid suggestions I might post.

      Comment

      • don250r
        New Member
        • Jul 2017
        • 5
        • USA

        #4
        Re: Element 40" TV

        Would these voltage tests be better with the PS board unplugged from the main board?

        Comment

        • dskall
          Badcaps Legend
          • Oct 2016
          • 2905
          • usa

          #5
          Re: Element 40" TV

          Voltages in standby and voltages when you push power button. Board plugged in
          I assume no responsibility for any stupid suggestions I might post.

          Comment

          • don250r
            New Member
            • Jul 2017
            • 5
            • USA

            #6
            Re: Element 40" TV

            I realized the stupidity of the question when i reread the standby and power voltages :P

            Comment

            Related Topics

            Collapse

            • Tynan Dill
              Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
              by Tynan Dill
              I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

              Upon bringing it home and plugging it up, it showed a standby light.

              I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

              The screen seems to blackout and stay black, but with a flashlight I can see the display.

              With my Playstation 4 connected via HDMI, and running a game I can hear sound.

              Assuming...
              11-22-2024, 01:46 PM
            • m1ch43lzm
              HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
              by m1ch43lzm
              Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
              Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
              05-12-2025, 08:37 PM
            • Hakuu
              LG OLED77G1PUA - No Video / Audio after a TCON Board change and Software Update
              by Hakuu
              Hi There,

              This TV was auto switching off after few seconds with some vertical lines on the screen, so got a new TCON board and replaced it.

              After replacing the TCON board it was working fine and i set it up with everything, used for few hours, then had the bright idea to update the software on it. During the update process, TV switched off and now no audio or video. No relay switch sound.

              More Details

              TV Model - LG OLED77G1PUA

              Got the same exact TCON board from TVPartsToday and replaced it. But didnt transfer the EPPROM data (didnt...
              07-12-2023, 02:37 PM
            • jb_Bak
              Sony xbr-65x900c main board issues?
              by jb_Bak
              Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.

              Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
              Power Board Connector that goes to Main board
              CN6401
              Pin 01 NC
              Pin 02 NC
              Pin 03 "BL_ON": 0V
              Pin 04 "N/C"
              Pin 05 "STBY 3.3V": 3.5V
              Pin 06 "GND": N/C
              Pin 07 "AC_OFF"...
              09-27-2021, 04:52 PM
            • canadaboy25
              Panasonic TC-P54VT25 No image. A or D board?
              by canadaboy25
              I have a Panasonic TC-P54VT25 that will power on and prime the display but there is no image at all.

              The panel is primed as there is a slight glow from the entire panel. This means the problem should be logic related. The service manual also confirms this and recommends replacing the A or the D board.

              I have tried to get the TV to display the test sequence but I have been unable to and I don't even know if this TV has a test sequence or not. I tried following tom66's instructions in post #3 on this thread https://www.badcaps.net/forum/showthread.php?t=26790. There was...
              01-17-2021, 01:06 AM
            • Loading...
            • No more items.
            Working...