Good day folks. Another common case of Samsung TV with incorrect colors, though not as bad as others, as the reds are actually displayed correctly while the blues are completely distorted or have a green tint. Anyhow it's not OK. I immediately figured something's wrong with the AS15-F gamma IC like it usually happens and upon removing the shield from the T-con board, this IC was burning hot, so I'm pretty sure that's the first sign right there. I haven't done any measurements to be fair. What worries me however is that this set has a separate board inbetween the main board and the T-con. I think they call it a LVDS board, though I'm not sure why it's needed, as other Samsung TVs don't have it (funnily enough I did repair one of these by replacing a 1uF cap on it). While I doubt there's something wrong with it (since the TV wouldn't display anything at all) I'd still like some advice on this - would replacing the AS15F solve the issue ? Cheers.
Samsung LE37a616A color issue (faulty AS15-F?)
Collapse
X
-
Re: Samsung LE37a616A color issue (faulty AS15-F?)
Change the AS15 buddy.Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !
https://www.facebook.com/Telford-Tel...7894576335359/ -
Wattevah...Comment
-
Re: Samsung LE37a616A color issue (faulty AS15-F?)
Wattevah...Comment
Related Topics
Collapse
-
This specification for the Samsung Galaxy Book 2 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Galaxy Book 2 boardview and Galaxy Book 2 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...09-07-2024, 05:50 AM
-
by vincentedelHello,
I'm having an issue with the Samsung 740n's phase control setting. When I use the automatic adjustment, it sets the value to around 54 (with a range of 0-100), and the picture looks clear and sharp. However, after some timeβlike after playing a gameβthe text starts to look blurry. When I auto-adjust again, it may increase the value to 80, and everything becomes sharp once more. Yet, after a while, whether it's a few hours or a day later, the same blurriness returns, and I have to adjust it again.
I'm using the Samsung 740n monitor drivers instead of the default plug-and-play...-
Channel: Troubleshooting Computer Displays
-
-
by ManucslHello.
My TV is a QE65Q800TATXXC Samsung TV.
Issue : When you plug the 220V, voltages are OK on the power board and you can hear the click from the relay, but TV is not starting when power button is pressed. Red led is blinking when you press power button. But no images or sound ( Back-light is off )
Then if you disconnect the cable from the main board to the power supply, the TV back-light turns on.
Any ideas to check would be very appreciated π
After reading some posts on this forum, I suspect an eeprom issue so I bought a CH341A to dump... -
by FourRunnerI purchased a used Samsung TV model UA65JS9000W recently knowing it had an issue with the screen. When switched on the picture was bright both sides of the screen but a little darker in the middle of the screen. Thinking this was the back lights (side mounted LCD strips) I replaced these, however the issue is still there. I am now thinking it may be a TCOM issue, but am not sure, any advice on this would be appreciated. Also whilst changing out the back lights I noticed the the thick clear plastic sheet (maybe 1.5 to 2mm thick) below the diffusers there is cracking (up to 75mm) on the sides and...1 Photo
-
by ScHAmPiHi all,
Because of two bright spots and a couple of dark spots I decided to replace the backlights in my Samsung UE48JU7000. See attached photos:
I thought all went well, but after full assembly and testing it out it turns out not all is fine. The backlights are completely fine but I have some weird issues on the right half of the screen. Since I didn't really touch the T-CON board (apart from taking out the ribbons of the display and reconnecting them on assembly) it would be weird that the issue is with the T-CON board... But based on the behavior of the service...2 Photos - Loading...
- No more items.
Comment